Best work boots

Six safety-toe work boots compared on the ratings their makers publish, with a finder that matches them to your job.

As an Amazon Associate I earn from qualifying purchases. How this site earns

KEEN Utility Cincinnati 6 in. waterproof work boot in brown leather with a black welt and soleKEEN Cincinnati 90°, carbon toe
Product photo: Amazon

Short answer

My top pick is the KEEN Cincinnati 90° Heel, with a carbon toe, EH and F3445 slip ratings, a waterproof liner and a Goodyear welt. Get the Irish Setter Ashby for hot asphalt or roofs, or the Thorogood for a USA-made boot.

On this page
  1. Short answer
  2. The picks
  3. The six picks, card by card
  4. Boot finder
  5. The six picks compared
  6. Safety ratings side by side
  7. Steel, aluminum or composite toe
  8. What an EH rating means
  9. Slip ratings, SR and ASTM F3445
  10. Waterproof, water resistant or neither
  11. Goodyear welt or cement construction
  12. Heat-resistant outsoles
  13. Sizes, widths and weight
  14. Cleaning, conditioning and when to replace
  15. Work boot recalls
  16. Where the sources disagree
  17. Which work boot fits you?
  18. Questions people ask
  19. How I pick work boots
  20. Related guides

Six safety-toe work boots

All six were new and in stock at my 7:07 AM check on Oct 22. Each is a men’s 6 in. lace-up boot with an ASTM F2413 safety toe, checked on the same five ratings.

KEEN Utility Cincinnati 6 in. waterproof work boot in brown leather with a black welt and soleProduct photo: Amazon
Best for wet sites and ladders

KEEN Cincinnati 90°

Cincinnati 90°, Coffee Bean/Black, 10 D

Buy it if You work on wet ground or ladders and want the most complete set of published safety ratings here.

Skip it if You walk on hot asphalt or roofing. The Ashby states a 475°F sole.

Full specs and the tradeoff
Timberland PRO Boondock 6 in. composite toe work boot in black leather with a rubber toe capProduct photo: Amazon
Best for wet, messy floors

Timberland Boondock

Boondock, black, 10

Buy it if Your work puts water or body fluids on your boots, and you want a liner rated for both.

Skip it if You want a fully stitched sole. The KEEN has a full Goodyear welt.

Full specs and the tradeoff
Ariat Rebar Lift 6 in. waterproof work boot in distressed brown leather with a moc toeProduct photo: Amazon
Best for a waterproof moc toe

Ariat Rebar Lift

Rebar Lift, Distressed Brown, 10.5 Wide

Buy it if You want a waterproof moc toe with a ladder heel and a stated outsole heat rating.

Skip it if You want a boot a cobbler can resole. The Ashby is welted and its maker says resoleable.

Full specs and the tradeoff
Thorogood American Heritage 6 in. moc toe work boot in Trail Crazy Horse brown leather with a white wedge-style heel soleProduct photo: Amazon
Best for a USA-made boot

Thorogood 804-4375

804-4375, Trail Crazy Horse, 10 D

Buy it if You want a moc-toe boot made in the USA that a cobbler can resole.

Skip it if You work in the wet or on hot surfaces. The Ariat is a waterproof moc toe with a heat rating.

Full specs and the tradeoff

Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.

The six picks, card by card

Best for wet sites and ladders

KEEN Cincinnati 90°

The Cincinnati is my top pick. It was new and in stock at my 7:07 AM check on Oct 22, sold by Amazon.com. The listing names model 1032622, and KEEN’s own page for the Cincinnati 6″ Waterproof 90° Heel Boot (Carbon Toe) carries the same number.

The safety toes are carbon, with separate left and right shapes. KEEN says they weigh 15% less than steel and give a lower-profile fit. The listing gives the ratings as ASTM F2413 M I/75 C/75 EH, plus ASTM F3445 for slip.

F3445 is ASTM’s newer slip-resistance standard, the newest slip standard named here. The listing adds ASTM F1677 Mark II, an older slip test, and SATRA TM31 for outsole abrasion. The rubber outsole is oil- and slip-resistant and non-marking.

Waterproofing is KEEN.DRY, a breathable membrane liner that KEEN says lets vapor out without letting water in. The listing adds a mesh liner that works with the membrane. That matches the Boondock and the Ariat.

The sole is stitched on with a continuous Goodyear welt, which KEEN tags as KEEN.WELT. Thorogood’s repair page says soles held on mainly with glue are the usual exception when a cobbler resoles boots, so a welt keeps that door open. KEEN itself doesn’t mention resoling.

The 90° heel gives the boot its name. KEEN says it adds stability and grip on soft ground, ladders and other uneven surfaces, and the listing says it helps catch or lock your foot in place. The listing gives the heel as 5/8 in.; KEEN’s product tags say 1/2 in.

The leather is KEEN’s barnyard-resistant full grain, which the listing says resists oleic acid, urea, sodium chloride and ammonium hydroxide. Cushioning is KEEN’s Luftcell, an air-infused midsole. KEEN tags the outsole as heat resistant but gives no temperature, so its heat claim has no figure to compare.

KEEN sells it in men’s 7 to 15, regular and wide. My call: the most complete set of published ratings here, for wet ground and ladder work.

Pros

  • ASTM F3445 slip and F2413 EH ratings
  • KEEN.DRY waterproof membrane
  • Continuous Goodyear welt
  • 90° heel for ladders and soft ground
  • Sizes 7 to 15, regular and wide

Cons

  • No heat temperature stated
  • Heel height differs by source
  • Weight not stated
  • Resoling not mentioned by KEEN
  • Listing is one size; pick yours on Amazon

Buy it if

You work on wet ground or ladders and want the most complete set of published safety ratings here.

Skip it if

You walk on hot asphalt or roofing. The Ashby states a 475°F sole.

Best for wet, messy floors

Timberland Boondock

The Boondock comes second and is the only pick whose waterproof liner carries a second rating. It was new and in stock at my 7:07 AM check on Oct 22, sold by Amazon.com. The listing names style TB1A1FZP001, which matches Timberland’s page for the Boondock 6″ Composite Toe Waterproof Work Boot.

Timberland says its membrane is waterproof and breathable and resists blood-borne pathogens as defined by ASTM F1671. That matters if your work puts fluids on your boots, and no other pick here names that test.

The toe is an asymmetrical composite cap that meets the ASTM F2413 impact and compression tests. In front of it sits a molded rubber toe protector that Timberland says is as thick as a standard boot outsole.

Timberland names EH protection to ASTM F2413 and F2892. Its SR icon, which the Boondock page shows, means the boot meets the slip requirements of F2413, F2892 or F3445 when tested to F2913. Both ratings are stated in full.

The build is a mix: a three-quarter Goodyear welt with a cemented heel, in Timberland’s words. That sits between a full welt and a cement build, because part of the sole is glued.

The outsole is Timberland’s All-Weather TPU, which it says stays flexible in changing weather and grips wet and frosted ice surfaces. The description calls it heat-, slip-, oil- and abrasion-resistant but gives no temperature.

Inside are Anti-Fatigue Technology polyurethane footbeds, OrthoLite insoles and a fiberglass shank, with a rigid external heel cup for side-to-side support. Timberland gives 2.43 lb for a men’s size 9, says the boot is imported, and sells it in medium and wide.

My call: the pick for wet, messy floors where a pathogen-resistant liner counts. The part-cement build and the missing heat figure are its tradeoffs.

Pros

  • Membrane rated to ASTM F1671 for blood-borne pathogens
  • EH to ASTM F2413 and F2892
  • SR slip rating
  • Molded rubber toe protector
  • Medium and wide widths

Cons

  • Part welt, part cement build
  • No heat temperature stated
  • Imported, per Timberland
  • Resoling not mentioned by Timberland
  • Listing is one size; pick yours on Amazon

Buy it if

Your work puts water or body fluids on your boots, and you want a liner rated for both.

Skip it if

You want a fully stitched sole. The KEEN has a full Goodyear welt.

Best for a waterproof moc toe

Ariat Rebar Lift

The Rebar Lift sits just behind the Boondock and is the only waterproof pick with a stated heat figure. It was new and in stock at my 7:07 AM check on Oct 22, sold by Amazon.com. The listing names style 10046876, which matches Ariat’s Rebar Lift 6″ Waterproof Composite Toe page.

Ariat lists ASTM F2413 for the composite toe, for EH and for slip resistance, and rates the boot I/C EH SRO. Its page says the boot meets ASTM’s highest standards for slip resistance. Both ratings are stated in full.

Waterproofing is Ariat’s DRYShield, a waterproof, breathable build. The listing describes it as waterproof full-grain leathers with an impermeable barrier, and Ariat says it helps keep feet dry on wet or muddy ground.

The sole is SMARTLITE TPU from Huntsman, oil- and slip-resisting. The listing says it passes the hot contact test at 150°C, or 302°F. That’s a stated temperature, though it’s lower than the Ashby’s 475°F.

It’s the only cement-built pick, per the listing, which means the sole is bonded rather than stitched. The cement build is the main thing holding it back. Thorogood’s repair page names glued soles as the usual exception when cobblers resole boots.

Like the KEEN, it has a 90° heel, which Ariat says gives secure footing on ladders, rungs and uneven surfaces. Ariat gives a 6 in. shaft, a 1.25 in. heel and a round moc toe.

Comfort parts are Ariat’s ATS support, a FLX Foam midsole and a removable All Day Cushioning insole. The upper is full-grain leather from Leather Working Group-certified tanneries, with a 50% recycled polyester lining. Ariat sells D and EE widths.

My call: a waterproof moc toe with a stated heat rating and a ladder heel. The cement build is its main tradeoff.

Pros

  • Hot contact test at 302°F (listing)
  • DRYShield waterproof build
  • ASTM F2413 EH and slip ratings
  • 90° heel for ladders and rungs
  • D and EE widths

Cons

  • Cement build, the only one here
  • Lower heat figure than the Ashby
  • Weight not stated
  • Resoling harder on a glued sole
  • Listing is one size; pick yours on Amazon

Buy it if

You want a waterproof moc toe with a ladder heel and a stated outsole heat rating.

Skip it if

You want a boot a cobbler can resole. The Ashby is welted and its maker says resoleable.

Best for hot asphalt and roofs

Irish Setter Ashby

The Ashby is the heat pick and the only aluminum toe here. It was new and in stock at my 7:07 AM check on Oct 22, sold by a third-party seller. The listing names model 83652, which matches Irish Setter’s page for the Ashby men’s 6-inch leather safety toe boot.

Irish Setter says roofers and paving contractors often work in high heat, and the Ashby’s HRO outsole is heat resistant to melting at a minimum of 475°F. That’s the highest outsole temperature any maker states on this page.

Irish Setter’s spec table lists ASTM F2413-24 I/C, EH and SR. The listing gives ASTM F2413-18 M/I/C EH and ASTM F3445-21 SR instead. Either way, EH and slip are both named in full.

The toe cap is aluminum. Irish Setter doesn’t give a weight saving over steel, so I don’t claim one. The outsole is its rubber-EVA Traction Tred.

Construction is Goodyear welt, and Irish Setter answers “Resoleable: Yes” in its spec table. It’s one of two picks whose maker says so. The listing adds that the welt helps keep water out of the boot.

It’s water resistant, not waterproof: the listing title says water resistant, and Irish Setter names no membrane. Water resistance is the Ashby’s one weak point. Pick a waterproof boot if you stand in water.

Inside is a removable polyurethane footbed over a Texon insole, on Irish Setter’s 325 last. The leather is oiled full grain. Irish Setter lists a weight of 3 lb 6 oz without saying for what size, sizes 7 to 14 in D or EE, and global sourcing.

Irish Setter is a Red Wing Shoe Co. brand, per its site footer. Its own store sells the same boot in a soft-toe version, style 83605, which isn’t a safety boot; check the model number on Amazon before you buy.

My call: the boot for hot asphalt and roofs. Its tradeoff is water resistance short of waterproof.

Pros

  • HRO sole rated to at least 475°F
  • Goodyear welt; maker says resoleable
  • EH and SR ratings
  • Aluminum safety toe
  • D and EE, sizes 7 to 14

Cons

  • Water resistant, not waterproof
  • Sold by a third-party seller, not Amazon
  • Globally sourced
  • ASTM edition differs by source
  • Listing is one size; pick yours on Amazon

Buy it if

You work on hot asphalt or roofing, or you want a welted boot its maker says can be resoled.

Skip it if

You stand in water. The KEEN and Ariat are waterproof.

Best for dry sites, steel toe

Timberland Pit Boss

The Pit Boss was the top pick on the old page. It was new and in stock at my 7:07 AM check on Oct 22, sold by Amazon.com. The listing names style TB133032001, which matches Timberland’s Pit Boss 6″ Steel Toe Work Boot page.

The toe is an asymmetrical steel cap. The listing gives ASTM F2413-18 I and C, and EH to ASTM F2413-18 and F2892-18. Timberland’s page shows its SR slip icon too, so EH and slip are both named.

The outsole is Timberland PRO rubber, which the listing calls heat resistant, with slip, oil and abrasion resistance. Timberland’s description says the same and adds non-marking. No temperature is given.

The sole is Goodyear welted; Timberland calls it a durable mechanical bond. That’s a full Goodyear welt, the same as the KEEN, the Ashby and the Thorogood.

It isn’t waterproof. Timberland makes no waterproof claim for the Pit Boss, and the upper is nubuck leather. It has no waterproofing, and that is why it sits fifth.

Comfort is Timberland’s 24/7 Comfort Suspension system, which it says supports the arch and cushions every step, plus a contoured shock-diffusion plate and a padded top collar. The lining is ReBOTL fabric with at least 50% recycled plastic and an antimicrobial treatment.

Timberland gives 2.83 lb for a men’s size 9. That’s 0.4 lb more than the Boondock at the same size, and the only like-for-like weight pair on this page, since both figures come from the same maker for the same size.

Timberland lists it as imported. I didn’t read a size or width range for the Pit Boss, so check the listing’s size menu for yours; the Boondock and KEEN both come in wide.

My call: a steel-toe welted boot for dry sites. No waterproofing is its main tradeoff.

Pros

  • Steel toe to ASTM F2413-18 I and C
  • EH and SR ratings
  • Goodyear welt
  • 24/7 Comfort Suspension system
  • Sold by Amazon.com

Cons

  • Not waterproof
  • No heat temperature stated
  • Imported, per Timberland
  • Sizes and widths not read
  • Listing is one size; pick yours on Amazon

Buy it if

You work on dry sites and want a welted steel-toe boot sold by Amazon.

Skip it if

Your site is wet. The Boondock is Timberland’s waterproof pick here.

Best for a USA-made boot

Thorogood 804-4375

The American Heritage 804-4375 is the one pick made in the USA. It was new and in stock at my 7:07 AM check on Oct 22, sold by a third-party seller. The listing names 804-4375, which matches Thorogood’s page for the American Heritage 6″ Trail Crazy Horse safety toe moc toe.

Thorogood says it’s made in the USA with USA and globally sourced components, from American leathers. The leather is Trail Crazy Horse full grain, which the listing says has a wax applied for an older look.

The toe is steel, rated to ASTM F2413-18 with EH, per the listing. The MAXWear 90 outsole has a heel and, the listing says, meets ASTM F3445-21 for slip. Thorogood’s own page calls it slip-resistant.

Construction is a Goodyear storm welt. Thorogood says that means you can re-sole the boots over the years, and its repair page points owners to cobblers. Note its warning: work by an outside cobbler voids Thorogood’s warranty.

Thorogood’s spec table says non-waterproof, unlined and non-insulated, and it names no heat-resistant outsole. Those two gaps are why it sits last of the six.

Comfort parts are a removable Ultimate Shock Absorption footbed on a Poron comfort cushion insole, and a composite shank. Thorogood says boots in the American Heritage line need no break-in time.

Sizes run 7 to 14 in D and EE. Thorogood’s warranty is one year against defects, and only for boots bought from an authorized seller with a receipt. Ask the Amazon seller whether it’s authorized if the warranty matters to you.

The listing names carpenters, electricians, pipefitters, plumbers, welders and HVAC workers among the trades it’s built for. Its “job-fitted” design, in Thorogood’s phrase, is meant for outdoor and industrial work.

My call: the moc toe for buyers who want a USA-made, resoleable boot. Its tradeoffs are no waterproofing and no heat claim.

Pros

  • Made in USA with USA and global parts
  • Goodyear storm welt; maker says resoleable
  • ASTM F3445-21 slip (listing)
  • EH rated
  • D and EE, sizes 7 to 14

Cons

  • Not waterproof, unlined
  • No heat claim
  • Sold by a third-party seller, not Amazon
  • Warranty needs an authorized seller
  • Outside resoles void the warranty

Buy it if

You want a moc-toe boot made in the USA that a cobbler can resole.

Skip it if

You work in the wet or on hot surfaces. The Ariat is a waterproof moc toe with a heat rating.

Which boot matches your job?

Tick what your workday involves. The finder keeps only the picks whose makers state that feature.

Boot finder

Every pick has an ASTM safety toe and an EH rating. Tick the conditions you work in.

All six picks match. Tick what your job involves to narrow them down.

Features as stated on the makers’ pages and the Amazon listings, read Oct 22, 2026.

The finder reads only what the makers publish. A boot that leaves a box unticked may still do the job; its maker just doesn’t say so. The ratings chart below shows each rating in full.

The six picks compared

From the makers’ pages and the Amazon listings. Scroll sideways on a phone; tap a header to sort on a computer.

PickToeSlipWaterproofBuildHeatBuy
KEEN Cincinnati 90°CarbonF3445MembraneWeltClaim onlyCheck it on Amazon
Timberland BoondockCompositeSRMembrane¾ welt + cement heelClaim onlyCheck it on Amazon
Ariat Rebar LiftCompositeSRDRYShieldCement302°FCheck it on Amazon
Irish Setter AshbyAluminumSR, F3445Water resistantWelt475°FCheck it on Amazon
Timberland Pit BossSteelSRNoWeltClaim onlyCheck it on Amazon
Thorogood 804-4375SteelF3445NoStorm weltNoneCheck it on Amazon

All six are men’s 6 in. lace-up boots with an ASTM F2413 safety toe and an EH rating. They differ in toe material, waterproofing, how the sole is attached and whether the outsole has a stated heat rating.

Safety ratings side by side

Every rating the makers publish for these six boots, in one chart.

PickToe capEHSlipWaterproofBuildHeat
KEEN Cincinnaticarbon toeEHASTM F3445 slipwaterproof membraneGoodyear weltheat-resistant claim with no temperature
Timberland Boondockcomposite toeEHSR slip ratingwaterproof membranethree-quarter Goodyear welt with cement heelheat-resistant claim
Ariat Rebar Liftcomposite toeEHSRDRYShield waterproofcement buildhot contact test at 302 degrees F
Irish Setter Ashbyaluminum toeEHASTM F3445 slipwater resistantGoodyear weltheat resistant to 475 degrees F
Timberland Pit Bosssteel toeEHSRnot waterproofGoodyear weltheat-resistant claim
Thorogood 804-4375steel toeEHASTM F3445 slipnot waterproofGoodyear storm weltno heat claim

The first three columns are a clean sweep: every pick names a safety toe, an EH rating and a slip rating. The differences sit in the last three. Three boots are waterproof, four are fully welted, and only two give an outsole temperature.

Steel, aluminum or composite toe

Every safety toe here meets the same ASTM F2413 impact and compression tests. The material changes the weight and whether the cap is metal.

Toe capPicksWhat the makers say
SteelPit Boss, ThorogoodMetallic, asymmetrical cap (Timberland listing); ASTM F2413-18 (both)
AluminumAshbyAn aluminum safety toe; no weight figure given
CarbonKEEN CincinnatiNon-metallic, 15% lighter than steel (KEEN)
CompositeBoondock, AriatNon-metallic, asymmetrical (Timberland); non-metallic (Ariat)

Is steel toe or composite toe better? On protection, the makers give the same answer: each cap meets ASTM F2413 for impact and compression. KEEN is the only maker here that puts a number on the weight difference, 15% lighter than steel for its carbon toe.

A non-metal cap matters if your site has metal detectors, but the cap is only one part. Eyelets and shanks can be metal too, and none of these makers calls its whole boot metal-free.

What an EH rating means

EH stands for electrical hazard. All six picks carry it, so it decides nothing between them, but it’s worth knowing what it covers.

PickEH rating as statedSource
KEEN Cincinnati 90°ASTM F2413 M I/75 C/75 EHListing
Timberland BoondockASTM F2413 and F2892, tested to F2412Timberland
Ariat Rebar LiftASTM F2413, EHAriat
Irish Setter AshbyASTM F2413-24 I/C, EHIrish Setter
Timberland Pit BossASTM F2413-18 and F2892-18Listing
Thorogood 804-4375ASTM F2413-18, EHListing, Thorogood

Timberland defines EH as secondary underfoot protection against live electrical circuits, energized conductors, parts or apparatus. Secondary is the key word: it backs up other measures. OSHA’s footwear rule, 29 CFR 1910.136, lists electrical hazards that remain after an employer takes other protective steps as one reason protective footwear is required.

If your employer issues a footwear spec, match the letters on the boot’s label to it.

Slip ratings, SR and ASTM F3445

Every pick names a slip rating, but they name different ones.

PickSlip rating as statedOutsole
KEEN Cincinnati 90°ASTM F3445; also F1677 Mark IIRubber, oil- and slip-resistant, non-marking
Timberland BoondockSR: F2413, F2892 or F3445 via F2913All-Weather TPU
Ariat Rebar LiftASTM F2413 slip resistant, SROSMARTLITE TPU
Irish Setter AshbySR (Irish Setter); F3445-21 (listing)Rubber-EVA Traction Tred
Timberland Pit BossSR iconTimberland PRO rubber
Thorogood 804-4375ASTM F3445-21 (listing)MAXWear 90 with heel

Timberland’s definition is the clearest one any maker gives here: SR means a boot meets the slip-resistance requirements of ASTM F2413, F2892 or F3445 when tested to ASTM F2913. F3445 is ASTM’s newer stand-alone slip standard, and three picks name it directly.

Slip grip wears with the tread. Thorogood’s repair page lists less traction than usual, or starting to slip, as a sign that boots need a new sole or replacing.

Waterproof, water resistant or neither

Three picks are waterproof, one is water resistant and two make no water claim.

PickWater claimHow the maker does it
KEEN Cincinnati 90°WaterproofKEEN.DRY breathable membrane liner
Timberland BoondockWaterproofWaterproof leather plus a breathable membrane, ASTM F1671
Ariat Rebar LiftWaterproofDRYShield waterproof, breathable build
Irish Setter AshbyWater resistantListing title; welt helps keep water out
Timberland Pit BossNone statedNubuck upper
Thorogood 804-4375Non-waterproofUnlined, per Thorogood

Timberland explains how it builds a waterproof boot: leathers sealed in tanning, then either sealed seams or an internal waterproof, breathable membrane, with gusseted tongues to stop water at the laces. KEEN and Ariat describe the same idea, a liner that keeps water out and lets vapor through.

Are waterproof work boots worth it? If you stand in water, mud or wet grass, yes. If you don’t, an unlined boot like the Thorogood skips the liner altogether. Thorogood suggests a leather waterproofing agent for boots that see moisture often.

Goodyear welt or cement construction

How the sole is attached decides whether a cobbler can replace it later.

PickConstructionMaker says resoleable?
KEEN Cincinnati 90°Continuous Goodyear weltNot stated
Timberland Boondock¾ Goodyear welt, cement heelNot stated
Ariat Rebar LiftCementNot stated
Irish Setter AshbyGoodyear weltYes
Timberland Pit BossGoodyear weltNot stated
Thorogood 804-4375Goodyear storm weltYes

A welted boot has a strip of leather stitched around it, and the sole is stitched to that strip. A cement boot has its sole bonded on. Thorogood’s repair page says most work boots can be resoled, with glued-on soles the main exception, as long as the upper is intact and the insole hasn’t cracked.

There’s a catch for safety boots. ASTM F2413’s scope warns that resoling, or adding an aftermarket footbed or insert, could make a boot fail the standard and void its ASTM marking. Ask the cobbler, or your safety officer, before resoling a rated boot you need for work.

Heat-resistant outsoles

Five picks say their outsole resists heat. Only two put a temperature on it.

PickHeat claimTemperature
Irish Setter AshbyHRO: resistant to meltingAt least 475°F
Ariat Rebar LiftPasses the hot contact test150°C (302°F)
KEEN Cincinnati 90°Heat-resistant outsole (product tag)Not stated
Timberland BoondockHeat-resistant TPU (description)Not stated
Timberland Pit BossHeat-resistant rubber (listing)Not stated
Thorogood 804-4375NoneNot stated

Irish Setter writes the Ashby’s heat claim for roofers and paving contractors, who work on hot surfaces, and names 475°F as the minimum its HRO soles resist melting at. Ariat’s 302°F is a hot contact test figure from the listing.

A claim with no number can’t be compared with a stated figure. If your work is on fresh asphalt or a hot roof, pick a boot with a stated temperature.

Sizes, widths and weight

Each Amazon listing I link is one size and color. Choose your own size on the listing before you buy.

PickSizesWidthsWeight as stated
KEEN Cincinnati 90°7 to 15Regular, wideNot stated
Timberland BoondockNot readMedium, wide2.43 lb, men’s size 9
Ariat Rebar LiftNot readD, EENot stated
Irish Setter Ashby7 to 14D, EE3 lb 6 oz, size not stated
Timberland Pit BossNot readNot read2.83 lb, men’s size 9
Thorogood 804-43757 to 14D, EENot stated

How should work boots fit? Start with the maker’s own size chart, since each brand cuts its own last. Irish Setter, for one, names the Ashby’s last, 325. At least five of the six come in a wide fit, so you don’t have to size up for width.

Plan your insole before you buy. ASTM F2413 warns that adding an aftermarket footbed or insert to a safety-toe boot could void its rating. The Ariat, Ashby and Thorogood ship with removable footbeds, per their makers.

Cleaning, conditioning and when to replace

Thorogood publishes the plainest care steps of any maker here. They apply to any leather work boot.

StepWhat Thorogood says
CleanWarm soapy water and a clean rag; brush the welt with a toothbrush if dirt builds up there
DryLet the boots dry before you condition or waterproof them, so moisture isn’t trapped
ConditionMonthly for hard wear, rain or heat; every 3 to 6 months for light wear
ProtectStore boots indoors; add a waterproofing agent if they’re often wet
Replace or resoleWhen the tread wears unevenly, traction drops, or the welt frays or separates

How long do work boots last? No maker here gives a number of months, because it depends on the job and the care. Thorogood says one of the main reasons leather cracks is that it dries out, which is why it stresses cleaning and conditioning.

How do you break in work boots? Thorogood says its American Heritage boots need no break-in time. The other makers don’t publish a break-in period, so wear new boots around the house for a few evenings before a full shift and check for rubbing.

Work boot recalls

I searched CPSC’s recall list since 2018 on Oct 22, 2026, for every brand on this page and for “work boot”.

SearchRecalls found
KEEN0
Timberland0
Ariat0
Irish Setter0
Thorogood0
“Work boot”2, both other brands (below)

The two work boot recalls, both from January 2024, were western pull-on boots. Boot Royalty recalled about 3,200 Justin Keaven met guard boots, model SE4570, because some could be missing the metatarsal guard. H.H. Brown recalled about 2,360 Redeemer DH5379 boots because the sole wasn’t puncture-resistant.

Neither brand is on this page. Keep your order page and the boot’s model number so you can match it to any notice at cpsc.gov/recalls.

Where the sources disagree

Places where a maker’s page and its Amazon listing don’t match. I go by the maker, then the listing.

TopicOne source saysAnother saysGo by
KEEN 90° heel height5/8 in. (listing)1/2 in. (KEEN product tags)KEEN
Ashby ASTM editionF2413-24 I/C EH SR (Irish Setter)F2413-18 M/I/C EH, F3445-21 SR (listing)Both; check the boot’s label
Thorogood shankComposite (Thorogood)Fiberglass (listing)Thorogood
Boondock waterproof testASTM F1671 (Timberland)ASTM F1671-07 (listing)Same test; the listing adds the year
Ariat slip labelSR (Ariat ratings box)SRO (Ariat feature list)Both appear on Ariat’s page

The two Ashby sources name different editions of ASTM F2413. Check the label inside the boot for the edition your pair carries, and match the model number on the listing to the maker’s page before you buy.

Which work boot fits you?

QuestionIf yesIf no
Does your employer require a safety toe and EH?Any pickAny pick, or a soft-toe boot
Do you work in water, mud or wet grass?KEEN, Boondock or AriatAny pick
Do you work on hot asphalt or roofs?Ashby (475°F) or Ariat (302°F)Any pick
Do you climb ladders or walk rebar?KEEN or Ariat (90° heel)Any pick
Do you want a boot you can resole?Ashby or ThorogoodAny pick
Does your site have metal detectors?KEEN, Boondock or Ariat (non-metal toe)Any pick
Do you want a boot made in the USA?ThorogoodAny pick

Start with what your employer requires, because that rules boots in or out. Then match the ground: wet sites want a waterproof liner, hot ones want a stated heat rating. Last, choose for comfort and life, like a ladder heel or a sole you can replace.

Kitting out for the job? My knee pad guide and tool bag guide cover the other gear you’ll carry and kneel on all day.

Questions people ask

What are the best work boots?

My top pick is the KEEN Cincinnati 90° Heel. It names a carbon safety toe, EH, ASTM F3445 slip resistance, a KEEN.DRY waterproof liner and a Goodyear welt. The Irish Setter Ashby is the pick for hot surfaces.

Are steel toe or composite toe boots better?

Both meet the same ASTM F2413 impact and compression tests. Composite and carbon caps are non-metallic, and KEEN says its carbon toe weighs 15% less than steel. Steel caps are what the Pit Boss and Thorogood use.

What does EH mean on work boots?

Electrical hazard. Timberland defines it as secondary underfoot protection against live circuits and energized parts. Every pick on this page carries an EH rating.

What is ASTM F2413?

ASTM’s performance specification for protective footwear. It sets minimum requirements, and its scope warns that resoling or adding an aftermarket insert could void the marking. OSHA’s footwear rule cites it.

How should work boots fit?

Use each maker’s own size chart, since lasts differ by brand. Five of my six picks come in a wide width, and the KEEN runs to size 15. Plan insoles first, because ASTM warns aftermarket inserts could void a safety rating.

How do you break in work boots?

Thorogood says its American Heritage boots need no break-in time. The other makers here don’t publish a break-in period, so wear new boots for short stretches at home before a full shift.

How do you clean work boots?

Thorogood’s steps: wash off dirt with warm soapy water and a rag, brush the welt, let them dry, then rub in leather conditioner and wipe off the excess. Leave them overnight before relacing.

How long do work boots last?

No maker here gives a lifespan. Thorogood lists the signs to resole or replace: tread worn unevenly, less traction than usual, or a welt that’s fraying or pulling away from the sole.

Are Timberland PRO boots good work boots?

Both Timberland PRO picks are in the six. The Boondock has a waterproof, pathogen-resistant liner, and the Pit Boss has no waterproofing.

What work boots are made in the USA?

On this page, only the Thorogood American Heritage 804-4375, which Thorogood says is made in the USA with USA and globally sourced parts. Timberland lists both its boots as imported, and Irish Setter says the Ashby is globally sourced.

How much do work boots cost?

Prices move often, so each card shows today’s Amazon price with the time I read it. The Thorogood and Ashby are sold by a third-party seller; the other four are sold by Amazon itself.

How I pick work boots

How I pick

I looked at one kind of product: men’s 6 in. lace-up work boots with an ASTM F2413 safety toe. Six boots from five makers are picks.

Every pick passed an offer read on Amazon at 7:07 AM on Oct 22, 2026: new, in stock and the buy-box winner. I matched each listing to the maker’s page by model or style number.

Ratings come from KEEN, Timberland, Ariat, Irish Setter and Thorogood, and from the Amazon listings where the maker is silent. Nothing here is taken from customer reviews.

Why trust me

I’m Isaac Daniels, and I own and edit Plain Buy Guides. Picks are built from the makers' specs, manuals, and safety-agency guidance. I read each maker’s product page, ASTM’s F2413 scope, OSHA’s footwear rule and Thorogood’s care, repair and warranty pages on Oct 22, 2026. Where a maker and its listing disagree, I show both. A CPSC search found no recalls for any brand here.

Sources

  • KEEN Utility (keenfootwear.com), Men’s Cincinnati 6″ Waterproof 90° Heel Boot (Carbon Toe), product page and product data
  • Timberland (timberland.com), Timberland PRO Boondock 6″ Composite Toe Waterproof and Pit Boss 6″ Steel Toe pages and feature definitions
  • Ariat (ariat.com), Rebar Lift 6″ Waterproof Composite Toe Work Boot, style 10046876
  • Irish Setter (irishsetterboots.com), Ashby men’s 6-inch leather safety toe boot, style 83652, tech specs
  • Thorogood (thorogoodusa.com), American Heritage 804-4375 product page, boot care, repair and restoration, and warranty pages
  • ASTM International, F2413-24 Standard Specification for Performance Requirements for Protective (Safety) Toe Cap Footwear, scope
  • OSHA, 29 CFR 1910.136, Foot protection
  • U.S. Consumer Product Safety Commission recall list via saferproducts.gov, searched by brand on Oct 22, 2026
  • Amazon listings for each pick, read Oct 22, 2026
  • Amazon offer read, Oct 22, 2026, 7:07 AM EDT