Our top pick is the Fowler 52‑520‑109‑0, a 1 in. AGD Group 2 indicator with both continuous and balanced readings. The white Fowler 110 reads 0–100 only. Graduation isn’t accuracy.
Best for reading plus or minus off zero$43.12 at AmazonPrice as of Nov 16, 2026, 5:34 AM EST
All three were new, in stock and sold by Amazon.com at our 12:27 PM check on Oct 26. Each is a plunger dial indicator with 1 in. of travel and 0.001 in. graduations, scored on the same ten checks.
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
The three indicators, card by card
Best for reading plus or minus off zero
Fowler 109 (black)
Fowler 52‑520‑109‑0 1 in. dial indicator with a black face
Both 0–100 continuous and 0–50–0 balanced readings, per Fowler
AGD Group 2, 2‑1/4 in. dial
About 2 oz of gauging force
3/8 in. stem and lug backs every 90°
Revolution counter and tolerance markers
Cons
1-year warranty, half of WEN’s
No accuracy figure on Fowler’s page
Fowler’s page and the listing disagree on the dial scales
Black face reads differently from a white one
Model 52‑520‑109‑01 in. range0.001 in.2‑1/4 in. dial3/8 in. stemAGD Group 2
Buy it if
You set zero on a part and read how far it moves either way, as when you check runout.
Skip it if
You only read straight up from zero and want a white face. The Fowler 110 is the white 0–100 dial.
The 52‑520‑109‑0 is Fowler’s 1 in. dial indicator with a black face. It was new and in stock at our 12:27 PM check on Oct 26. It scores 10.0, tied with its white-face sibling; it ranks first on our tie rule because Fowler’s page lists both continuous and balanced readings for it.
Fowler’s page gives AGD Group 2, a 1 in. range and 0.001 in. graduations, with a 0–100 continuous reading and a 0–50–0 balanced reading. A balanced dial counts out from zero both ways, which is handy when you set zero on a part and watch how far it moves to each side.
Fowler’s catalog table puts the dial at 2‑1/4 in. across (its Dim. A) with a 3‑3/8 in. Dim. B, and draws the stem at 3/8 in. with a 4‑48 NF thread at the contact point and a 1/4 in. hole in the lug. Those numbers matter when you fit it to a magnetic base or holder.
The page lists the build: a revolution counter hand, lug backs positioned through 90° increments, a spindle rack and contact points of hardened stainless steel, and a forged brass, satin-chromed case. Fowler says the movement is mounted on its own rigid plate, separate from the case, for permanent alignment.
Gauging force is published, which WEN’s page doesn’t do. Fowler says Group II and III gages measure with approximately 2 oz of pressure, except its 0.0001 in. models at 5 oz. Extra-long springs, Fowler says, keep that pressure even through the whole travel.
The knurled bezel turns through 360°, so you can set zero at any needle position, and Fowler includes adjustable tolerance limit markers. Set them at the top and bottom of your tolerance and you can see at a glance whether a reading falls inside.
Fowler’s warranty chart gives its dial indicators one year. The Amazon listing says the same. That is the only place it trails WEN, which offers two. Fowler publishes no accuracy figure for this model, and neither does WEN for the 10703.
Our call: the indicator to buy if you read plus and minus around zero. It scores 10.0, a full ten on the facts its maker publishes.
Best for straight 0–100 readings
Fowler 110 (white)
Fowler 52‑520‑110‑0 1 in. dial indicator with a white face
The listing claims a balanced scale Fowler’s spec table doesn’t list
Model 52‑520‑110‑01 in. range0.001 in.2‑1/4 in. dial3/8 in. stemAGD Group 2
Buy it if
You measure travel or depth and read straight up from zero.
Skip it if
You want to read plus and minus off zero. The Fowler 109 adds the 0–50–0 scale.
The 52‑520‑110‑0 is Fowler’s 1 in. dial indicator with a white face. It was new and in stock at our 12:27 PM check on Oct 26. It scores 10.0, tied with the black-face 109 and second on our tie rule.
Fowler’s spec table for it lists AGD Group 2, a 1 in. range, 0.001 in. graduations and a 0–100 continuous reading, and its catalog table shows a dash in the balanced column. By that table it reads one way: up from zero, round and round, with the counter keeping track of each tenth of an inch.
Fowler isn’t consistent here. The description text on the same Fowler page mentions graduations in black for continuous readings and red for balanced readings, and the Amazon listing says 0–100 and 0–50–0. We follow Fowler’s spec table and catalog, which list no balanced scale, and show the conflict in the table below. Check the dial photo before you buy if you need a balanced scale.
Size and mounting match the 109. Fowler’s catalog gives a 2‑1/4 in. dial and a 3 in. Dim. B, a 3/8 in. stem, a 1/4 in. lug hole and a 4‑48 NF contact thread. Fowler supplies it with lug backs positioned through 90° increments.
The build is the same family: hardened stainless spindle rack and contact points, a forged brass satin-chromed case, hard brass gear wheels and silver steel pinions. Fowler says it meets AGD specifications and measures with approximately 2 oz of pressure.
A knurled bezel turns through 360°, and Fowler includes an adjustable tolerance limit marker. Fowler also notes the dial is available in metric graduations, sold as other models.
Warranty is one year on Fowler’s chart, and the listing says one year too. Fowler publishes no accuracy figure for it, which is normal for these pages: the graduation tells you how finely it reads, not how close each reading is to true.
Our call: a white-face indicator for straight-up readings. It scores 10.0, on Fowler’s own published facts.
No accuracy figure, despite the “maximum accuracy” wording
Model 107031 in. range0.001 in.2 in. face1/4 in. lug hole1‑1/2 in. plunger
Buy it if
You want the longest warranty and a manual with runout steps.
Skip it if
You need the gauging force on paper. Both Fowler picks list about 2 oz.
The 10703 is WEN’s 1 in. dial indicator. It was new and in stock at our 12:27 PM check on Oct 26. It scores 9.0, third of three and still well over 7.0.
WEN’s page says it meets ASME and ANSI standards. It lists a 0.001 in. resolution on the outer dial and a 0.1 in. resolution on the inner wheel, which counts how many times the big hand has gone round. Together they read anywhere in the 1 in. range.
WEN calls the 0.001 in. resolution “maximum accuracy”. Resolution and accuracy aren’t the same thing: resolution is the smallest step the dial shows. WEN publishes no accuracy figure, so we don’t score one, for this or either Fowler.
The face is 2 in. across, a little smaller than Fowler’s 2‑1/4 in. The plunger is 1‑1/2 in. long by 3/16 in., spring-loaded, and the back has a 1/4 in. lug hole for mounting on a magnetic base. WEN sells bases for it, the 10711 and 10714.
The rack and contact tip are stainless steel. A rotatable bezel lets you turn the face so zero lines up with the needle, and adjustable markers give reference points. WEN’s manual adds a bezel lock that holds the bezel in place.
WEN’s manual has runout steps. Set the plunger at 90° to the part, press it about halfway down and lock the indicator in place. Turn the part one full turn, set zero at the needle’s farthest counterclockwise point, then turn it again: the farthest the needle goes clockwise is the runout. Our calculator does the same subtraction.
The manual the 10703 page links to is labeled model 10702, with the same 0–1 in. range, 0.001 in. and 0.1 in. dials and 0.25 in. mounting hole. We note it below. WEN gives a two-year warranty, the longest here, plus a stocked inventory of replacement parts and a customer helpline at 1‑800‑232‑1195.
Our call: the pick for a longer warranty and a clear manual. It scores 9.0, held back only by no published gauging force.
Work out a reading and the runout
Enter the lowest and highest readings you saw as the part turned, and your tolerance. The calculator gives the total indicator reading (TIR) and whether it’s inside.
Runout (TIR) calculator
Read the turn counter and the big dial, then type each reading in inches.
To total one reading, add the turn counter and the big dial.
Enter your lowest and highest readings to see the runout. Readings are in inches; on these dials each mark is 0.001 in. and each full turn of the big hand is 0.100 in.
Arithmetic only: TIR is the highest reading minus the lowest. Counter turns are 0.100 in. each and marks 0.001 in., per Fowler and WEN.
TIR is just the highest reading minus the lowest. WEN’s manual gets the same number another way: set zero at the needle’s lowest point, then read the highest. The calculator also shows how to add the turn counter to the dial, since each full turn of the big hand is 0.100 in. on all three picks.
The answer can only be as good as the setup. WEN’s manual says to keep the plunger at 90° to the part and lock the indicator so it can’t move. A reading finer than the dial’s 0.001 in. steps is a guess between marks.
The three indicators compared
From the makers’ pages and documents. Scroll sideways on a phone.
Plain Buy Guides spec score out of 10. Ten published facts, one point each; it’s our arithmetic, not a customer rating.
All three read in 0.001 in. steps. None of the three makers publishes an accuracy figure for these models.
Term
What it means here
What the makers publish
Graduation (Fowler) / resolution (WEN)
The smallest step marked on the dial
0.001 in. on all three
Range
How far the plunger travels
1 in. on all three
Turn counter
Counts full turns of the big hand
Each turn is 0.100 in.; WEN calls it a 0.1 in. inner dial
Accuracy
How close a reading is to the true value
Not published for these models
Standard named
A standard the maker says it meets
Fowler: AGD Group 2. WEN: ASME and ANSI
A dial marked in thousandths doesn’t promise every reading is right to a thousandth. That would be accuracy, and none of these pages states it. Fowler names the AGD group and WEN names ASME and ANSI, and we score that as a published standard, without turning it into a number the makers didn’t print.
If you need a stated accuracy, Fowler sells premium indicators with a NIST certificate of calibration on its own site. They weren’t among the Amazon.com-sold listings in our search on Oct 26.
A continuous dial counts 0 to 100 all the way round, which suits measuring how far something moved. A balanced dial counts out from 0 in both directions to 50, which suits checking a part that wobbles either side of a setting. The Fowler 109 has both; Fowler describes black graduations for continuous and red for balanced readings on its dials.
Stem, lug and contact point
These sizes decide which bases, holders and points fit.
Indicator
Stem
Lug hole
Contact thread
Plunger
Back
Fowler 109 / 110
3/8 in.
1/4 in.
4‑48 NF
Not stated
Lug backs every 90°
WEN 10703
Not stated
1/4 in.
Not stated
1‑1/2 × 3/16 in.
Lug back
The 1/4 in. lug hole on all three is what a magnetic base clamps to. Fowler’s 3/8 in. stem fits holders that grip the stem instead. Fowler sells a replacement ball contact point, part 05‑100‑176, and its catalog lists back plate screws and a top screw as spares.
Gauging force and build
Gauging force is how hard the plunger presses on the part. Fowler publishes it; WEN doesn’t.
Indicator
Gauging force
Rack and tip
Case
Fowler 109 / 110
About 2 oz (Group II and III, except 0.0001 in. models at 5 oz)
Hardened stainless steel
Forged brass, satin-chromed
WEN 10703
Not stated
Stainless steel
Not stated
Force matters on soft or thin parts, where a firm plunger can push the part instead of measuring it. Fowler also says extra-long springs keep the pressure uniform through the whole travel. WEN describes its plunger as spring-loaded and says it retracts easily and smoothly.
Warranty
From each maker’s own pages.
Maker
Warranty for these models
Source
Fowler
1 year
Fowler warranty chart: dial indicators
WEN
2 years
WEN 10703 product page
Fowler’s chart lists longer terms only for other lines, such as some Sylvac-made electronics with registration. Its plain dial indicators are one year. WEN pairs its two years with stocked replacement parts and a phone helpline.
The indicators we checked and left out
All sold by Amazon.com and new on Oct 26. Each lacked a maker page to score against, or isn’t in stock or the same kind.
Indicator checked
Status
Why it isn’t a pick
Fowler 52‑520‑485‑0 with magnetic back
Before scoring
Not on Fowler’s site, so there’s no maker page to score
Brown & Sharpe (TESA) 14.82023
Before scoring
No maker page found; the listing’s model field reads 599‑9749‑12
Central Tools 4345
Before scoring
No maker page; listing warranty is repair only up to 90 days
Mitutoyo 2046A
Before scoring
Not available at Amazon.com on Oct 26
Dial test indicators and digital indicators
Before scoring
Different kinds of indicator
Brown & Sharpe’s 14.82023 may well be a fine indicator. Its listing describes 0.001 in. graduations, a revolution counter and a 2‑1/4 in. rotating dial. We couldn’t tie it to a maker page, and its model field doesn’t match the part number, so it can’t pass our listing check.
Where the sources disagree
Where a maker’s page and the Amazon listing say different things.
Topic
Maker says
Listing says
We use
Fowler 109 scales
0–100 continuous and 0–50–0 balanced
0–100 continuous
Fowler’s page
Fowler 110 scales
Spec table and catalog: 0–100 continuous only; Fowler’s description text mentions red balanced graduations
Black 0–100 and red 0–50–0
Fowler’s spec table and catalog
WEN manual
Linked from the 10703 page
Labeled model 10702
Same specs; noted
WEN accuracy wording
“Maximum accuracy”
Same
Not scored: no figure given
Recalls
We searched the CPSC recall list on Oct 26, 2026.
Search
Recalls found
Dial indicator
None
Fowler
None
WEN dial indicator
None
How to choose a dial indicator
Answer these in order. Each answer narrows the picks.
Question
If yes
If no
Do you read plus and minus around zero, as for runout?
Fowler 109 (balanced 0–50–0)
Next question
Do you want a white face that reads straight up?
Fowler 110
Next question
Do you want the longest warranty?
WEN 10703 (2 years)
Either Fowler
Do you need a published accuracy figure?
None of these; look for a calibration certificate
Any pick
Match the dial to the job first, then the mounting: all three take a base on the 1/4 in. lug. If you’re setting up a drill press or checking a chuck, a balanced dial makes the wobble easy to read. Keep the indicator with your mechanic’s tools in its box, since a dropped indicator can lose its setting.
Questions people ask
What is the best dial indicator?
Our top pick is the Fowler 52‑520‑109‑0, which scores 10.0. It’s a 1 in. AGD Group 2 indicator with both continuous and balanced readings. The white-face Fowler 110 also scores 10.0.
What is a dial indicator used for?
Measuring small movements: runout on a shaft or chuck, flatness, height differences and how far a part moves. WEN’s manual describes measuring runout.
Is resolution the same as accuracy?
No. Resolution or graduation is the smallest step on the dial: 0.001 in. on all three picks. Accuracy is how close a reading is to the true value, and none of these makers publishes a figure for these models.
How do you read a dial indicator?
Add the turn counter to the big dial. On these picks each full turn of the big hand is 0.100 in., and each mark on the big dial is 0.001 in. Our calculator adds them for you.
How do you measure runout with a dial indicator?
WEN’s manual: set the plunger at 90° to the part, press it about halfway, lock the indicator, turn the part, set zero at the lowest point, then turn again and read the highest. That’s the runout.
What is TIR?
Total indicator reading: the highest reading minus the lowest as the part turns. It’s what our calculator works out.
What does AGD mean on a dial indicator?
It’s the specification Fowler says these indicators meet; both Fowler picks are AGD Group 2, with a 2‑1/4 in. dial in Fowler’s table.
What’s the difference between continuous and balanced dials?
A continuous dial counts 0 to 100 all the way round. A balanced dial counts out both ways from 0 to 50. The Fowler 109 has both scales.
What size stem does a dial indicator have?
Fowler’s catalog gives a 3/8 in. stem and a 1/4 in. lug hole for these models. WEN lists a 1/4 in. lug hole.
How much force does a dial indicator press with?
Fowler says about 2 oz for its Group II and III indicators, except 0.0001 in. models at 5 oz. WEN doesn’t publish a figure for the 10703.
How much does a dial indicator cost?
Prices change, so each card shows today’s Amazon price with the time we read it. Our scores don’t use price.
How we pick dial indicators
How we pick
We looked at one kind of product: plunger dial indicators with 1 in. of travel and 0.001 in. graduations. Every listing passed an offer read on Amazon at 12:27 PM on Oct 26, 2026: new, in stock, sold by Amazon.com and the buy-box winner. We matched each pick to its maker’s page by model number.
Ten checks, one point each, make the score out of 10. A fact the maker doesn’t publish scores 0. Ties go to the maker page that lists both continuous and balanced readings.
Why trust us
Isaac Daniels, who owns Plain Buy Guides, edits this page. We read Fowler’s product pages, catalog table and warranty chart, WEN’s product page and manual, and the CPSC recall list, all on Oct 26, 2026. We don’t state accuracy figures the makers don’t publish.
The ten checks, part one: the maker publishes the range; the graduation; a standard it meets; the gauging force; and the dial diameter.
Part two: a stem or lug size; a turn counter; a bezel and tolerance markers; a warranty term on its own pages; and a model number that matches the Amazon listing.
The spec score, check by check
Indicator
Range
Graduation
Standard named
Gauging force
Dial size
Mounting size
Turn counter
Bezel and markers
Maker warranty
Listing match
Score
Fowler 109 (black)
1
1
1
1
1
1
1
1
1
1
10.0
Fowler 110 (white)
1
1
1
1
1
1
1
1
1
1
10.0
WEN 10703
1
1
1
0
1
1
1
1
1
1
9.0
Sources
Fowler High Precision (fowlerprecision.com), product pages for 525201090 and 525201100, and warranty chart
Fowler High Precision catalog, Indicators section, p. 112 dial indicator table (PDF linked from the 525201090 page)
WEN Products (wenproducts.com), 10703 product page and the linked dial indicator instruction manual (model 10702)
U.S. Consumer Product Safety Commission recall API, searched Oct 26, 2026
US keyword data for dial indicator, pulled Oct 26, 2026; Google results read Oct 26, 2026
Amazon listings for each indicator, read Oct 26, 2026