Best scroll saw for a home shop

For a home shop scroll saw, get the DeWalt DW788 when you want a 20 inch throat and a table that tilts both ways. [1] For the lower-cost bench saw, the WEN 3921 takes pin-end or plain-end blades on a 16 inch throat. [3]

Illustration of a generic gray scroll saw with a thin blade on a wooden workbench
Disclaimer: Illustration for visual purposes

Top pick

DeWalt DW788

Best for: a 20 inch throat and a table that tilts both ways. [1]

The downside: You pay more, and it takes 5 inch plain-end blades only. [1]

Check it on Amazon: DeWalt DW788

As an Amazon Associate I earn from qualifying purchases.

Isaac Daniels

Written by Isaac Daniels, owner and editor

How we chose · About

: added a warranty table for the six saws.

How we picked

We compared 6 scroll saws using maker manuals and spec sheets.

Picks by need

Two saws from WEN, and one each from DeWalt, JET, SKIL and Dremel.

DeWalt DW788, product photo from its exact Amazon listing
Product photo from Amazon

DeWalt DW788

For both tilt directions and a longer reach

Best for: A cut past 16 inches, or a bevel to the right. [1] [3]

Skip it if: You already own pin-end blades. This saw takes 5 inch plain-end blades only. [1]

What sets it apart: The only table here that tilts both ways. [1]

The tradeoff: You pay more than for the 16 inch saws here. [3] [5] [7]

Check it on Amazon: DeWalt DW788
WEN 3923, product photo from its exact Amazon listing
Product photo from Amazon

WEN 3923

For easier blade changes

Best for: A side panel and a work light on a 16 inch saw. [5]

Skip it if: You need a right tilt, or you want to turn a pinned blade 90 degrees. That turn is on the 3921. [3] [5]

What sets it apart: The side panel opens for the blade change. [5]

The tradeoff: You pay more than the 3921 for that panel and the light. [5]

Check it on Amazon: WEN 3923
WEN 3921, product photo from its exact Amazon listing
Product photo from Amazon

WEN 3921

For the lower-cost bench saw

Best for: Pin-end or plain-end blades. [3]

Skip it if: You want the 3923 side panel, a right tilt, or spiral blades. [3]

What sets it apart: A pinned blade can turn 90 degrees. [3]

The tradeoff: The table tilts left only, and the throat is shorter than the DW788. [3]

Check it on Amazon: WEN 3921
JET JWSS-22B, product photo from its exact Amazon listing
Product photo from Amazon

JET JWSS-22B

For the longest reach

Best for: A cut farther than 20 inches, with the arm doing the tilt. [6] [1]

Skip it if: You want pin-end blades. [6]

What sets it apart: The longest throat here, and the arm tilts instead of the table. [6]

The tradeoff: You pay more, and it weighs 68.2 pounds. [6]

Check it on Amazon: JET JWSS-22B
SKIL SS9503-00, product photo from its exact Amazon listing
Product photo from Amazon

SKIL SS9503-00

For a foot pedal

Best for: Hands stay on the board, with pin-end or plain-end blades. [7]

Skip it if: You need a right tilt, or a bevel thicker than 3/4 inch. [7]

What sets it apart: The only 16 inch saw here that includes a foot pedal. [7]

The tradeoff: You give up a right tilt, and a bevel is thinner than a square cut. [7]

Check it on Amazon: SKIL SS9503-00
Dremel MS20-01, product photo from its exact Amazon listing
Product photo from Amazon

Dremel MS20-01

For a small board

Best for: Work that fits a 9.84 inch throat, including a lift-off cut in wood. [8]

Skip it if: You need a 5 inch bench blade, a listed thickness, or a tilt. [8] [1]

What sets it apart: It lifts off its base for hand-held cuts in wood. [8]

The tradeoff: A short throat, its own short blades, and no tilt. [8]

Check it on Amazon: Dremel MS20-01

Compare the six saws

Figures in this table are maker specs.

Six scroll saws
Model Throat Cut at 90 degrees Blade Tilt Speed Buy
DeWalt DW788 [1] 20 inches [1] 2 inches [1] 5 inch plain-end only [1] Table, 45 degrees left and right [1] 400 to 1,750 strokes per minute [1] Check it on Amazon: DeWalt DW788
WEN 3923 [5] 16 inches [5] 2 inches [5] 5 inch pin-end and pinless [5] Table, 0 to 45 degrees left [5] 550 to 1,600 strokes per minute [5] Check it on Amazon: WEN 3923
WEN 3921 [3] 16 inches [3] 2 inches [3] 5 inch pin-end and pinless [3] Table, 0 to 45 degrees left [3] 550 to 1,600 strokes per minute. The product page also lists 400 to 1,600. Read the label on the saw. [3] [4] Check it on Amazon: WEN 3921
JET JWSS-22B [6] 22-3/8 inches [6] 2 inches [6] 5 inch plain-end [6] Arm, 45 degrees left and 45 degrees right [6] 400 to 1,550 strokes per minute [6] Check it on Amazon: JET JWSS-22B
SKIL SS9503-00 [7] 16 inches [7] 2 inches. 3/4 inch at 45 degrees. [7] 5 inch pin-end and pinless [7] Table, 0 to 45 degrees left [7] 550 to 1,650 strokes per minute [7] Check it on Amazon: SKIL SS9503-00
Dremel MS20-01 [8] 9.84 inches [8] Not listed by the maker [8] 3.8 inch Moto-Saw blades [8] Not listed by the maker [8] 1,500 to 2,250 no-load speed [8] Check it on Amazon: Dremel MS20-01

Who should buy it, and who shouldn't

The DW788 fits a shop that needs reach and a bevel either way. Leave it if the blades you own are pin-end.

The 3923 fits frequent blade changes when you also want the light. Leave it if you need the turned pin slot on the 3921.

The 3921 fits the lower cost when the blades you own already match the saw.

The JET fits fretwork that sits farther out than the other saws on this page.

The SKIL fits a cut where the switch should leave both hands on the board.

The Dremel fits a small board, or wood that has to stay where it is.

Will this board fit

Answer what you know. A blank, or Not sure, still names a saw.

Leave it blank if you are not sure. You can turn the board.

Use a square cut. The SKIL drops to 3/4 inch when the table is at 45 degrees. [7]

More options

This checks the numbers on these six saws. It cannot replace the setup in the instruction manual, or a look at the board.

What warranty does each saw state?

Warranty as the maker states it
Saw Warranty
DeWalt DW788 The instruction manual says one year. The product page says 3 Year Limited Warranty, 1 Year Free Service, and 90 Days Satisfaction Guaranteed. Those two lines differ. [1] [2]
WEN 3921 Two years for personal use. [3]
WEN 3923 Two years for personal use. [5]
JET JWSS-22B Five years for woodworking. Two years for industrial or commercial use. [6]
SKIL SS9503-00 Three years if you register within 30 days. Otherwise the home-use term is one year. [7]
Dremel MS20-01 Two years from the purchase date. [8]

How to choose a scroll saw

How far is the cut from the nearest edge?

Decide that distance, then turn the board. Throat is the distance from the blade to the body column. [6] A 16 inch throat reaches the middle of a 32 inch board. Each saw's throat is in the comparison table.

Which blade end should you buy?

Match the end in the comparison table before you buy a pack. For an inside cut on the DW788, drill a pilot hole so the blade can pass through. [1]

How does the blade change for an inside cut?

The 3923 opens a side panel. The DW788 uses two thumbscrews. The 3921 has a second slot for a pinned blade. On the JET, the blade goes in after it passes through the work. The SKIL sets a plain-end blade in the adaptors. [1] [3] [5] [6] [7]

What speed matches the material?

The DW788 manual says to slow down for metal, plastic, harder wood, and very thin material. [1] WEN and SKIL call for very slow speeds on precious and non-ferrous metals. [3] [5] [7] Each saw's speed is in the comparison table. On the Dremel, hard material and acrylic want a slower speed. [8]

How should the saw sit on the bench?

A shaking bench shows in the curve. WEN mounts on a stable surface, and a soft foam pad you supply cuts the noise. [3] [5] The JET uses rubber washers, or four foot pads if you do not bolt it. [6] The DW788 and the SKIL each have three mounting holes. [1] [7] The Dremel station clamps or bolts to the bench. [8]

Which saws clear the dust?

The DW788 has an adjustable air hose that blows dust off the cut. [1] Each WEN has a sawdust blower and a blade-guard foot. The 3921 has an adjustable light. [3] [5] The SKIL has a sawdust blower, an LED, and a drop foot. [7]

Which blades come in the box?

WEN 3921 and 3923 include a 15 TPI pinned blade, an 18 TPI pinned blade, and an 18 TPI pinless blade. Thin wood, 1/4 inch or less, wants a very fine, narrow blade. [3] [5] Buy the blade end in the comparison table.

Questions buyers ask

What size scroll saw fits the board?

The JET reaches 22-3/8 inches from the nearest edge, the DW788 reaches 20 inches, the WEN and SKIL saws reach 16 inches, and the Dremel reaches 9.84 inches. Turn the board to use the other side. [6] [1] [3] [5] [7] [8]

How thick can these scroll saws cut?

The five bench saws cut 2 inches at a square cut. On the SKIL, a bevel drops to 3/4 inch. The Dremel thickness is not listed by the maker. [1] [3] [5] [6] [7] [8]

Pin-end or plain-end blades?

The DW788 and the JET take plain-end blades only. The two WEN saws and the SKIL take pin-end or plain-end blades. The Dremel uses its own blades. [1] [6] [3] [5] [7] [8]

Is a 16 inch throat enough?

Yes, when the cut stays within 16 inches of the nearest edge. A 16 inch throat reaches the middle of a 32 inch board. A farther cut needs a longer throat in the table. [6]

Does the table or the arm tilt?

The DW788 table tilts both ways. The JET arm tilts both ways. The WEN and SKIL tables tilt left only. The Dremel tilt is not listed by the maker. [1] [6] [3] [5] [7] [8]

Can a scroll saw replace a jigsaw or a band saw?

No. A scroll saw is for fine curves in a limited thickness. A jigsaw is a handheld saw for rougher curves, and a band saw handles thicker stock. Use the scroll saw whose throat, blade, and thickness match the board.

Recalls and saws left off the list

A recall check on November 6, 2026, from January 1, 2018 through that day, found no recall for the DW788, WEN 3921, WEN 3923, JET JWSS-22B, SKIL SS9503-00, or Dremel MS20-01. That check is not a safety certification. [9]

Each saw on this list was sold new by Amazon or its maker, with a public manual, and no brand has more than two. On November 6, 2026, Delta, Excalibur, Pegas, and Shop Fox did not meet that, so they are not listed. [10]

Sources

  1. DeWalt DW788 instruction manual, form 383329. 20 inch size, speed 400 to 1,750, 2 inch maximum, table bevel 45 degrees left and right, thumbscrew clamps, arm lift, plain-end blades, one-year warranty.
  2. DeWalt DW788 product page. Double parallel-link arm. Warranty line: 3 Year Limited Warranty, 1 Year Free Service, 90 Days Satisfaction Guaranteed.
  3. WEN 3921 instruction manual. Pinned blade turned 90 degrees, pin-end and pinless blades, two-year personal-use warranty.
  4. WEN 3921 product page. The feature list says 400 to 1,600 strokes per minute. The description on the same page says 550 to 1,600.
  5. WEN 3923 instruction manual. Side panel locks, work light, pin-end and pinless blades.
  6. JET JWSS-22B operating instructions, part M-727200B, edition 5, October 2018. Throat definition, plain-end blades, arm tilt, and the warranty terms.
  7. SKIL SS9503-00 owner's manual. Foot pedal, pin-end and plain-end blades, drop foot, and the warranty terms.
  8. Dremel MS20 operating instructions. Speed, throat, stroke, weight, blade length, hand-held and stationary modes, and a two-year warranty.
  9. U.S. Consumer Product Safety Commission recall list. Checked from January 1, 2018 through November 6, 2026.
  10. Price and stock check for these six saws, November 6, 2026, 8:22 PM UTC. The prices on this page drop off after 24 hours.