
Best right angle drills
Six drills for rough-in and tight spots, matched to the holes you bore.

Quick answer
For most rough-in, get the Bosch GRD18V-127HXB26X kit: two speeds, kickback control, 5 in. hole saws and two batteries. For holes past 5 in., get Milwaukee’s 2811-22 kit. On Milwaukee M18, the 2808-20 is lighter.
Top pick: Bosch GRD18V-127HXB26X kit
Check it on Amazon
Best for most plumbing rough-in → Bosch GRD18V-127HXB26X kit, 18V
Best for holes up to 6 in. → Milwaukee 2811-22 Super Hawg kit
Best for 2-9/16 in. holes on M18 → Milwaukee 2808-20 Hole Hawg, tool only
Best for Makita 18V LXT owners → Makita XAD06Z 18V LXT, tool only
Best for DeWalt 20V MAX owners → DeWalt DCD446B 20V MAX XR, tool only
As an Amazon Associate I earn from qualifying purchases. Disclosure.
On this page
Top picks
Five genuine branded stud and joist drills, each new and in stock when re-checked Nov 11, 2026, 1:24 AM EST. Prices are read from Amazon and show the time they were read.





The biggest hole each drill is rated for
Hole capacity is the first spec to check. It decides which pipe sizes you can bore for without switching tools.
Bosch GRD18V-127HX: the all-round rough-in drill
Best for most plumbing rough-in
Bosch GRD18V-127HXB26X 18V right angle drill kit



Pros
- Two speeds: 0–550 and 0–1,800 RPM
- 5 in. hole saws, 2-9/16 in. self-feed bits
- Dual KickBack Control
- Two 6 Ah batteries and a charger in the box
- Five-year limited warranty on Bosch 18V tools
Cons
- Bosch’s page lists low gear as 500 in one spot and 550 in another
- Listed weight doesn’t say if a battery is on
- No holes-per-charge figure
Buy it if
You bore drain, vent and supply holes through studs, plates and joists, and you want kickback control and batteries in one box.
Skip it if
You already own a drawer full of Milwaukee M18 or Makita LXT batteries. A tool-only drill on your own batteries makes more sense.
This is the pick for most rough-in work. Bosch rates it for 2-9/16 in. holes with self-feed bits and 5 in. holes with hole saws. That covers drain and vent holes through plates, and a 3 in. drain through a 2x12 joist when you stay inside the code limits in the chart below.
It has two speed settings. The Amazon listing gives 0–550 and 0–1,800 RPM. Bosch’s own page shows the low gear as 500 RPM in its bullets and 550 RPM in its description. Either way, low gear is for big bits and high gear spins small augers fast.
Dual KickBack Control is the feature to look at first. Bosch says it helps slow down or stop the tool in a bind-up, to cut the risk of a sudden reaction. My read: on a big self-feed bit that hits a knot or a nail, that’s the moment you want the tool to back off.
The chuck is a 7/16 in. quick chuck. Bosch says it gives fast, tool-free bit changes. The Milwaukee and Makita drills here also list a 7/16 in. chuck, while DeWalt uses a 1/2 in. keyed chuck, so check your bits’ shanks before you switch brands.
This is the only full-size drill here that comes with batteries. The box has two EXPERT 18V 6 Ah batteries and a GAL12V/18V-80 charger. Bosch’s listing says the batteries are part of AMPShare, a battery system shared across several brands.
Bosch lists 6.8 lb and 16.6 in. long, with an in-line design for tight spaces and an LED light. It doesn’t say if 6.8 lb includes a battery. Makita and Milwaukee state their with-battery weights, so compare with care.
Bosch’s 18V cordless tools carry a five-year limited warranty, per the listing. Bosch doesn’t publish a holes-per-charge number, so its run time can’t be lined up against DeWalt, Makita or Milwaukee.
My call: kickback control, 5 in. hole saw capacity and two batteries in the box make this the easiest all-round buy for plumbing rough-in.
Milwaukee 2811-20 Super Hawg: for the biggest holes
Best for holes up to 6 in.
Milwaukee 2811-22 M18 FUEL Super Hawg kit

Pros
- Rated for 6 in. hole saws in low gear
- Up to 100 2-9/16 in. holes through 6 in. beams per charge
- All-metal Quik-Lok chuck and side handle
- Mechanical clutch in low speed
- Five-year tool warranty
- Runs on any M18 battery
Cons
- Heaviest here: 14.4 lb with battery
- 20.5 in. long
Buy it if
You bore holes past 5 in. or through thick beams every week, and you already run M18 batteries.
Skip it if
Most of your holes are 2-9/16 in. or smaller. The Bosch does that at about half the weight (6.8 lb), and the Hole Hawg is lighter too (9.5 lb).
If your holes run past 5 in., this is the drill on the list built for them. Milwaukee says its POWERSTATE brushless motor keeps constant power under heavy load to get through 6-1/4 in. holes. No other drill here is rated that big.
Milwaukee pitches it as a cordless drill with the power and speed to replace corded right angle drills. It claims up to 100 holes of 2-9/16 in. through 6 in. beams per charge on an M18 REDLITHIUM HIGH OUTPUT XC6.0 battery.
That’s a beam-thick test, not a single stud, so the number doesn’t line up with the other makers’ claims. Milwaukee says the run time covers the rough-in of a single-family home, or several multi-family units, on one charge. Your bits and lumber will change that.
The chuck is an all-metal 7/16 in. Quik-Lok. Milwaukee says you can put attachments in and take them out with one hand. The side handle is all metal too, and an LED light covers the work area.
For safety, Milwaukee lists a mechanical clutch in low speed. It doesn’t list a kickback system like Bosch’s or DeWalt’s. My read: with a hole saw this size, keep the side handle on and plan your stance before you pull the trigger.
The cost is size and weight. Milwaukee lists 12.1 lb without a battery, 14.4 lb with one, and 20.5 in. long. That’s about twice Bosch’s listed 6.8 lb, and it takes more room between joists.
The top speed is 1,550 RPM. Milwaukee’s manual gives low gear as 0–500 RPM. The tool carries a five-year limited warranty and the battery three years, per Milwaukee. It comes as a kit with two XC6.0 batteries and a rapid charger, and the drill runs on any M18 battery.
My call: buy it if big holes through thick lumber are a weekly job. If they aren’t, the Bosch is lighter and fits the bay better.
Milwaukee 2808-20 Hole Hawg: the lighter M18 option
Best for 2-9/16 in. holes on M18
Milwaukee 2808-20 M18 FUEL Hole Hawg, tool only



Pros
- Up to 220 7/8 in. holes per charge on an HO XC6.0
- Milwaukee calls it its lightest right angle drill
- 9.5 lb with battery, 15.6 in. long
- Quik-Lok chuck
- Top handle
- Five-year limited warranty
Cons
- Self-feed bits stop at 2-9/16 in.; hole saws at 4 in.
- Top speed listed as 1,500 and 1,550 RPM in different spots
- No clutch or kickback system listed
Buy it if
You run M18 batteries and most of your holes are for supply lines, 1-1/2 in. drains and 2 in. drains in 2x6 walls.
Skip it if
You bore for 4 in. drains. Its hole saws stop at 4 in., and a 4 in. pipe needs more than 4-1/2 in.
The Hole Hawg is the smaller of the two Milwaukee drills. Milwaukee rates it through 2-9/16 in. self-feed bits and 4 in. hole saws. The self-feed size is the same one Bosch, Makita and DeWalt list as their limit. Milwaukee calls it its lightest right angle drill.
Milwaukee lists 7.09 lb without a battery and 9.5 lb with one, and 15.6 in. long. Against the Super Hawg, that’s about 5 lb lighter and 5 in. shorter, which matters when you’re drilling overhead through joists all day.
Run time is the headline claim. Milwaukee says up to 220 holes of 7/8 in. per charge on an M18 REDLITHIUM HIGH OUTPUT XC6.0 battery, and it pitches the drill for the fastest rough-ins. Milwaukee doesn’t say what lumber it used.
The chuck is Milwaukee’s 7/16 in. Quik-Lok, and the box also has a chuck key. Milwaukee lists an ergonomic top handle for comfort and an LED light for the work area.
The top speed is a small puzzle. Milwaukee’s spec table shows 0–1,550 RPM in one field and 0–1,500 in another. The lower number is the one listed. Milwaukee doesn’t list a second gear.
Milwaukee doesn’t list a clutch or a kickback system on this page. The bigger Super Hawg lists a mechanical clutch in low speed, and Bosch and DeWalt list systems that slow or shut off the tool. My read: on this drill, your grip and stance are the safety system.
It carries a five-year limited warranty and runs on any M18 battery. It’s sold tool only, so add a battery if you don’t own one.
Its spec score loses most on hole size and kickback: Milwaukee rates it to 4 in. hole saws and lists no clutch or kickback system for it, where the Super Hawg has a mechanical clutch in low.
My call: if you’re on M18 and your holes top out at 4 in., this is the lighter, shorter way to do it.
Makita XAD06Z: two speeds and an electric brake
Best for Makita 18V LXT owners
Makita XAD06Z 18V LXT, tool only
Makita XAD06Z 18V LXT brushless 7/16 in. hex right angle drill, tool only



Pros
- Two speeds: 0–450 and 0–1,400 RPM
- 5 in. hole saws, 2-9/16 in. self-feed, 1-1/2 in. ship auger
- Electric brake
- Dual LED lights
- Tool-less 7/16 in. hex sleeve
- Side handle fits either side
Cons
- No kickback system listed
- Weight listed as 7.3 lb and 7.6 lb with battery
- Three-year warranty, shorter than Bosch and Milwaukee
Buy it if
You already run Makita 18V LXT batteries and want a full-size rough-in drill with a low gear for big bits.
Skip it if
Kickback control is high on your list. Bosch and DeWalt list it; Makita’s page doesn’t.
Makita’s XAD06Z lists the same capacity as the Bosch: 5 in. holes with hole saws and 2-9/16 in. holes with self-feed bits. It adds a figure the others don’t give, 1-1/2 in. with a ship auger bit.
It has a two-speed transmission. Low gear is 0–450 RPM and high is 0–1,400 RPM. Low gear is the one for hole saws and self-feed bits, and high gear is for augers and smaller holes.
Weight is the selling point. Makita’s bullets say 7.3 lb with battery, and its spec table says 7.6 lb. Either figure puts it close to the Bosch, and Makita adds a slim barrel to cut fatigue. It’s 17-1/8 in. long.
The bit holder is a tool-less 7/16 in. hex sleeve, and Makita says the drill uses 7/16 in. hex shank bits. There’s an electric brake, dual LED lights and a metal gear housing. The side handle mounts on either side.
Run time comes two ways. Makita’s page says up to 105 holes of 1-1/2 in. per charge in 2x SPF lumber. The Amazon listing says up to 200 holes of 7/8 in. in 2x SPF on a 5.0 Ah battery. Those use different bits, so neither lines up with DeWalt’s or Milwaukee’s claims.
Makita doesn’t list a kickback system. The electric brake stops the bit when you let off the trigger, which is a different job. My read: if you’ve had a drill wrench your wrist before, Bosch’s or DeWalt’s system is worth more than the brake.
The warranty is three years, shorter than the five years Bosch and Milwaukee list. It’s sold tool only and runs on Makita’s 18V LXT batteries.
My call: on Makita batteries, this is the one to get.
DeWalt DCD446B: anti-rotation and a 1/2 in. keyed chuck
Best for DeWalt 20V MAX owners
DeWalt DCD446B 20V MAX XR, tool only
DeWalt DCD446B 20V MAX XR compact stud and joist drill, tool only



Pros
- ANTI-ROTATION system with a red LED
- 1/2 in. keyed chuck
- 4 in. hole saws, 2-9/16 in. self-feed bits
- Up to 267 7/8 in. holes per charge (DCB2108)
- Tool Connect chip-ready
Cons
- 4 in. hole saw limit, the lowest of the full-size drills
- One max speed listed: 1,250 RPM
- DeWalt lists 11.3 lb assembled
- Three-year warranty
- Tool only
Buy it if
You run DeWalt 20V MAX batteries and want a drill that shuts itself off if it starts to spin.
Skip it if
You need holes past 4 in. Bosch and Makita list 5 in. and the Super Hawg 6 in.
DeWalt’s stud and joist drill has the clearest safety feature on the list. Its ANTI-ROTATION system senses when the tool body starts to rotate too much and shuts it down. A red LED lights up when the system steps in, so you know why it stopped.
Capacity is 4 in. with a hole saw and 2-9/16 in. with a self-feed bit. That’s enough for a 3 in. drain, which needs a hole bigger than its 3-1/2 in. outside diameter, but not for a 4 in. drain.
The chuck is a 1/2 in. keyed chuck, with a chuck key and key holder in the box. The other full-size drills here use 7/16 in. chucks, so this is the one that takes the 1/2 in. shank bits from a regular drill.
DeWalt’s run-time claim is up to 267 holes per charge, using a 7/8 in. by 18 in. auger bit in 1.5 in. thick Douglas fir, on a DCB2108 battery. That’s the most specific test any maker here gives.
Power depends on the battery. DeWalt says the drill puts out up to 1,845 max watts with a DCB2108 battery, 79% more than with a DCB205. If you plan on big holes, plan on the bigger battery too.
DeWalt lists a max speed of 1,250 RPM and doesn’t list a second gear. Its spec table gives an assembled weight of 11.3 lb, an 18.54 in. length and a 5.59 in. height. Plan for the size in tight joist bays.
It’s Tool Connect chip-ready, so a contractor can track it with DeWalt’s site manager app once a chip is added. The chip is sold separately. The warranty is three years limited, with one year of free service and a 90-day satisfaction guarantee.
My call: on DeWalt batteries, the anti-rotation system makes this an easy pick for 2-9/16 in. work.
Checked and left out: the Bosch PS11-102
Bosch’s PS11-102 is a 12V, 3/8 in. drill/driver with a five-position head. Bosch lists it at 2.4 lb in its spec table and 2 lb 12 oz in its own feature bullet, and 11.5 in. long, and its Amazon listing caps it at a 3/4 in. spade bit. That makes it a service tool for pilot holes and screws inside cabinets, not a stud and joist drill, so it scores 6.4 on the checks the five drills above share (How it’s scored).
| Drill | Spec score | What held it back | What it does well |
|---|---|---|---|
| Bosch PS11-102 12V kit | 6.4 | 3/4 in. spade bit at most; no holes-per-charge figure listed | Shortest here at 11.5 in.; 90° to 180° head; battery and charger in the box |
All six drills side by side
Tap the length header to sort on desktop. Spec score: How it’s scored.
| Drill | Spec score | Photo | Battery | Chuck | Speeds (RPM) | Hole saw max | Self-feed max | Length (in.) | Kickback system | Warranty | Buy |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Bosch GRD18V-127HX Most plumbing rough-in | 8.6 | ![]() | 18V, 2 x 6 Ah included | 7/16 in. quick | 0–550 / 0–1,800 | 5 in. | 2-9/16 in. | 16.6 | Dual KickBack Control | 5 yr | Check it on Amazon |
| Milwaukee 2811-22 Holes up to 6 in. | 8.6 | ![]() | M18 kit, two XC6.0 | 7/16 in. Quik-Lok | Top 1,550 | 4 in. high, 6 in. low | 2-9/16 in. high, 4-5/8 in. low | 20.5 | Mechanical clutch in low | 5 yr | Check it on Amazon |
| Milwaukee 2808-20 2-9/16 in. holes on M18 | 8.0 | ![]() | M18, tool only | 7/16 in. Quik-Lok | Top 1,500 | 4 in. | 2-9/16 in. | 15.6 | Not listed | 5 yr | Check it on Amazon |
| Makita XAD06Z Makita 18V LXT owners | 7.8 | ![]() | 18V LXT, tool only | 7/16 in. hex | 0–450 / 0–1,400 | 5 in. | 2-9/16 in. | 17.1 | Not listed (electric brake) | 3 yr | Check it on Amazon |
| DeWalt DCD446B DeWalt 20V MAX owners | 8.4 | ![]() | 20V MAX, tool only | 1/2 in. keyed | Max 1,250 | 4 in. | 2-9/16 in. | 18.5 | ANTI-ROTATION | 3 yr | Check it on Amazon |
From the makers’ pages and the Amazon listings, read Oct 19, 2026, and Milwaukee’s manuals, read Nov 11, 2026. “Not listed” means the maker doesn’t state it, not that the drill lacks it. Milwaukee’s manual rates the 2808-20 through 2-9/16 in. self-feed bits and 4 in. hole saws.
Will your pipe fit? Hole sizes and code limits
This is the chart the other pages don’t publish. It puts the pipe’s outside diameter next to the biggest hole the code allows in each piece of framing.
Two numbers decide every hole. The hole has to be bigger than the pipe’s outside diameter, and it can’t be bigger than the code’s limit for that stud or joist. The limits below are from the 2021 International Residential Code (IRC), the model code many states and cities adopt for houses.
Your city or county may have adopted a different edition or local changes, so check with your inspector before you bore anything structural.
| Framing | Actual depth | Biggest bored hole | Edge rule | IRC section |
|---|---|---|---|---|
| 2x4 stud, bearing or exterior wall | 3-1/2 in. | 1.40 in. (40%); up to 2.10 in. if the stud is doubled | 5/8 in. from each edge | R602.6 |
| 2x4 stud, nonbearing wall | 3-1/2 in. | 2.10 in. (60%) | 5/8 in. from each edge | R602.6 |
| 2x6 stud, bearing or exterior wall | 5-1/2 in. | 2.20 in. (40%); up to 3.30 in. if the stud is doubled | 5/8 in. from each edge | R602.6 |
| 2x6 stud, nonbearing wall | 5-1/2 in. | 3.30 in. (60%) | 5/8 in. from each edge | R602.6 |
| 2x8 joist | 7-1/4 in. | 2.41 in. (1/3 depth) | 2 in. from top and bottom | R502.8.1 |
| 2x10 joist | 9-1/4 in. | 3.08 in. (1/3 depth) | 2 in. from top and bottom | R502.8.1 |
| 2x12 joist | 11-1/4 in. | 3.75 in. (1/3 depth) | 2 in. from top and bottom | R502.8.1 |
Actual depths are the dry dressed sizes in NIST’s American Softwood Lumber Standard (PS 20). Hole limits are from IRC 2021 R602.6 (studs) and R502.8.1 (sawn joists), worked out from the code text and rounded down to the hundredth. In a bearing wall, the code allows no more than two doubled studs in a row to be bored past 40%.
| Pipe | Outside diameter | 2x4 nonbearing | 2x6 bearing | 2x6 nonbearing | 2x10 joist | 2x12 joist |
|---|---|---|---|---|---|---|
| 1/2 in. copper | 0.625 in. | Fits | Fits | Fits | Fits | Fits |
| 3/4 in. copper | 0.875 in. | Fits | Fits | Fits | Fits | Fits |
| 1 in. copper | 1.125 in. | Fits | Fits | Fits | Fits | Fits |
| 1-1/2 in. PVC Sch 40 | 1.900 in. | Fits, tight | Fits | Fits | Fits | Fits |
| 2 in. PVC Sch 40 | 2.375 in. | Too big | Double the stud | Fits | Fits | Fits |
| 3 in. PVC Sch 40 | 3.500 in. | Too big | Too big | Too big | Too big | Fits, tight |
| 4 in. PVC Sch 40 | 4.500 in. | Too big | Too big | Too big | Too big | Too big |
Copper outside diameters are from the Copper Development Association’s Copper Tube Handbook (always 1/8 in. larger than the size name). PVC outside diameters are from Spears’ Schedule 40 dimension sheet. “Fits” means a hole bigger than the pipe still falls inside the limit; “tight” means 1/4 in. of room or less.
| Pipe | Hole needed | Drills rated for that hole |
|---|---|---|
| 1/2 in. copper | Over 0.625 in. | All six |
| 3/4 in. copper | Over 0.875 in. | All but the PS11 (3/4 in. spade bit max) |
| 1 in. copper to 2 in. PVC | Over 1.125 to over 2.375 in. | The five 18V and 20V drills (2-9/16 in. self-feed) |
| 3 in. PVC | Over 3.500 in. | Bosch 127HX, Makita, DeWalt, Super Hawg, Hole Hawg |
| 4 in. PVC | Over 4.500 in. | Bosch 127HX, Makita, Super Hawg |
Read the 3 in. row twice. A 3 in. PVC drain is 3-1/2 in. across, which is more than a 2x6 stud allows and more than a 2x10 joist allows. A 2x12 joist allows 3.75 in., so the hole has to be bigger than 3-1/2 in. and no bigger than 3-3/4 in.
For a 3 in. stack in a 2x6 wall, the IRC’s exception allows stud shoes installed per the maker’s instructions where approved. Ask your inspector first.
A 4 in. drain doesn’t fit through any sawn joist up to a 2x12 under these limits. Plan that run below, beside or parallel to the joists instead of through them.
Top plates, I-joists and trusses
Two more code rules catch plumbers out. One covers the plate at the top of a wall, the other covers engineered framing.
- 1Measure the plate hole
IRC R602.6.1 applies when piping in an exterior or bearing wall cuts, drills or notches the top plate by more than 50% of its width. On a 2x4 plate that’s any hole over 1-3/4 in.
- 2Add a metal tie
Fasten a galvanized tie at least 0.054 in. thick (16 gauge) and 1-1/2 in. wide across the opening, to the plate on each side.
- 3Nail it right
Use at least eight 10d nails (0.148 in. diameter, 1-1/2 in. long minimum) on each side, or an equivalent.
- 4Run it long
The tie has to extend at least 6 in. past the opening. The code waives the tie when that whole side of the wall is covered by wood structural panel sheathing.
IRC R502.8.2 prohibits cuts, notches and holes in trusses, I-joists, glulam and other engineered members unless the maker allows it or a registered design professional designs for it. Find the maker’s hole chart before you drill.
R602.6 says a bored hole can’t be in the same section of stud as a cut or notch. Bore or notch, not both.
In sawn joists, R502.8.1 keeps each hole at least 2 in. from any other hole and from the top and bottom edges.
Speed and gears: why low gear matters
A big hole saw or self-feed bit wants low speed and high torque. A small auger wants speed. A two-speed drill gives you both.
| Drill | Low gear | High gear | What the maker says about gears |
|---|---|---|---|
| Bosch GRD18V-127HX | 0–550 RPM | 0–1,800 RPM | Fast drilling for standard work, more torque for demanding tasks |
| Makita XAD06Z | 0–450 RPM | 0–1,400 RPM | Two-speed transmission for a wide range of drilling |
| Milwaukee 2811-20 | 0–500 RPM | 0–1,550 RPM | Mechanical clutch in low speed |
| Milwaukee 2808-20 | Not listed | 0–1,500 RPM | No second gear listed |
| DeWalt DCD446 | Not listed | 1,250 RPM max | No second gear listed |
| Bosch PS11 | Variable speed trigger | 0–1,300 RPM | Single range with a variable-speed trigger |
Speed alone doesn’t tell you which drill bores faster. Torque in low gear does the work on big bits, and only Bosch’s PS11 lists a torque figure here. So use the speed chart to see which drills have a second gear, not to rank them.
My read: for rough-in, a listed low gear is worth having. Bosch and Makita state theirs, and Milwaukee’s Super Hawg lists a low speed with a clutch.
Kickback: which drills help when a bit binds
When a big bit binds, the drill body wants to spin instead of the bit. Three makers here list a feature for that moment.
GRD18V-127HX. Bosch says it helps slow down or stop the tool in a bind-up to reduce the risk of a sudden reaction.
DCD446. Senses excessive rotation of the tool and shuts it down; a red LED shows it stepped in.
2811-20 Super Hawg. Milwaukee lists a mechanical clutch in low speed.
Milwaukee 2808-20 and Makita XAD06Z. Makita lists an electric brake, which stops the bit when you release the trigger. That’s a different job.
None of these features replaces a good grip. Keep the side handle on when the drill has one, and read the manual’s section on bracing before you run a big bit.
My call: if you’re new to angle drills, buy one of the three with a listed system. Bosch and DeWalt describe systems that slow or shut off the tool for you.
Holes per charge: why the claims don’t compare
Every maker but Bosch gives a holes-per-charge number. They all use a different bit, lumber or battery, so read each one on its own.
| Drill | Maker’s claim | Bit | Lumber | Battery |
|---|---|---|---|---|
| DeWalt DCD446 | Up to 267 holes | 7/8 in. x 18 in. auger | 1.5 in. Douglas fir | DCB2108 |
| Milwaukee 2808-20 | Up to 220 holes | 7/8 in. | Not listed | M18 HIGH OUTPUT XC6.0 |
| Makita XAD06Z | Up to 200 holes (Amazon listing) | 7/8 in. | 2x SPF | 5.0 Ah |
| Makita XAD06Z | Up to 105 holes (Makita page) | 1-1/2 in. | 2x SPF | 5.0 Ah |
| Milwaukee 2811-20 | Up to 100 holes | 2-9/16 in. | 6 in. beams | M18 HIGH OUTPUT XC6.0 |
| Bosch GRD18V-127HX | Not listed |
The Super Hawg’s 100 holes look smallest, but each one is 2-9/16 in. through a 6 in. beam. That’s far more wood per hole than a 7/8 in. hole through a 2x. So the number to trust is the one that matches your work.
Battery size moves these numbers too. DeWalt says its drill puts out 79% more max watts on a DCB2108 than on a DCB205, so the battery you own changes both power and hole count.
Size and weight between the joists
A right angle drill earns its name between joists. Length and weight decide how easy it is to hold there.
| Drill | Weight as listed | Battery on? | Length | Height |
|---|---|---|---|---|
| Bosch PS11 | 2.4 lb (bullet: 2 lb 12 oz) | Not stated | 11.5 in. | Not listed |
| Bosch GRD18V-127HX | 6.8 lb | Not stated | 16.6 in. | 7.4 in. |
| Makita XAD06Z | 7.3–7.6 lb | Yes | 17-1/8 in. | Not listed |
| Milwaukee 2808-20 | 9.5 lb (7.09 bare) | Yes | 15.6 in. | 6.5 in. |
| DeWalt DCD446 | 11.3 lb | Not stated | 18.54 in. | 5.59 in. |
| Milwaukee 2811-20 | 14.4 lb (12.1 bare) | Yes | 20.5 in. | 7.3 in. |
From each maker’s spec table, read Oct 19, 2026. Makita lists 7.3 lb in its feature list and 7.6 lb in its spec table. DeWalt’s figure is listed as assembled product weight.
The weights aren’t all measured the same way, so treat small gaps as a tie. The big gap is real: the Super Hawg is about twice the weight of the Bosch 127HX or the Makita.
Height matters for the space between joists. DeWalt lists the lowest height of the full-size drills that give one, at 5.59 in. My read: in a tight crawlspace, measure your joist depth against these numbers before you buy.
Chucks: 7/16 in. hex, 1/2 in. keyed or 3/8 in.
The chuck decides which bits you can use. Check it against the bits you already own.
| Chuck | Drills | What the maker says |
|---|---|---|
| 7/16 in. quick chuck | Bosch GRD18V-127HX | Fast, tool-free bit changes |
| 7/16 in. Quik-Lok | Milwaukee 2811-20, 2808-20 | All metal on the 2811-20; insert and remove attachments with one hand |
| 7/16 in. hex sleeve | Makita XAD06Z | Tool-less; uses 7/16 in. hex shank bits |
| 1/2 in. keyed | DeWalt DCD446 | Chuck key and key holder included |
| 3/8 in. auto-lock keyless | Bosch PS11 | Simple bit changes for small bits and drivers |
Makita says its drill uses 7/16 in. hex shank bits, so check that your self-feed and auger bits have that shank before you buy. A 1/2 in. keyed chuck holds round shanks, which is why the DeWalt takes the bits from a regular 1/2 in. drill.
Tool only or kit: what’s in the box
Three of the six are sold tool only. That’s fine if you already own the batteries, and a surprise if you don’t.
| Drill | In the box | Battery platform |
|---|---|---|
| Bosch GRD18V-127HXB26X | Drill, two EXPERT 18V 6 Ah batteries, GAL12V/18V-80 charger | Bosch 18V, AMPShare |
| Bosch PS11-102 | Drill, 12V Max 2.0 Ah battery, charger, carrying bag | Bosch 12V Max |
| Milwaukee 2811-22 | Drill, two XC6.0 batteries, rapid charger, contractor bag, side handle | Any M18 |
| Milwaukee 2808-20 | Drill, chuck key | Any M18 |
| Makita XAD06Z | Drill, 20 in. tool bag, tool hook, side handle | Makita 18V LXT |
| DeWalt DCD446B | Drill, chuck key, key holder | DeWalt 20V MAX |
My read: stay on the battery platform you already own unless a feature pulls you away. If you own none, the Bosch kit and the Super Hawg kit are the ones that work out of the box. My Makita combo kit and DeWalt combo kit guides cover starter sets with batteries.
Which drill fits the work you do
| Your work | Pick | Why |
|---|---|---|
| New construction rough-in, no batteries yet | Bosch GRD18V-127HX kit | 5 in. hole saws, kickback control, two batteries in the box |
| Big holes through beams and thick lumber | Milwaukee 2811-22 kit | Rated through 6 in. holes |
| Supply and 2 in. drain holes on M18 | Milwaukee 2808-20 | Lighter, 220 7/8 in. holes per charge claimed |
| Rough-in on Makita batteries | Makita XAD06Z | Two speeds, 5 in. hole saws, electric brake |
| Rough-in on DeWalt batteries | DeWalt DCD446B | ANTI-ROTATION, 1/2 in. keyed chuck |
| Service work inside cabinets | Bosch PS11-102 | 2.4 lb (bullet: 2 lb 12 oz), five-position head, 3/8 in. chuck |
Start with the biggest pipe you bore for. If it’s 3 in. drain, rule out the PS11; the Hole Hawg’s 4 in. hole-saw rating covers it. If it’s 4 in., you’re down to the Bosch 127HX, the Makita and the Super Hawg, and the code chart above says where that hole can go.
Then match your batteries. A drill on batteries you already charge every night beats a slightly better drill on a second platform.
Questions people ask
Is a right angle drill worth it?
For rough-in, yes. Drain, vent and supply holes go through studs and joists that sit close together, and a regular drill won’t fit between them square. These drills put the bit at 90° to the body and are rated for 2-9/16 in. self-feed bits or more.
What is the most compact right angle drill?
Of the six here, Bosch’s PS11 is the smallest: 2.4 lb per Bosch’s spec table, 2 lb 12 oz in Bosch’s own bullet, and 11.5 in. long per Bosch, with a 3/8 in. chuck. Among the full-size drills, Milwaukee’s 2808-20 is the shortest at 15.6 in., and Milwaukee calls it its lightest right angle drill.
What is the best angle drill tool?
For most rough-in work, the buy is the Bosch GRD18V-127HXB26X kit. It’s rated for 5 in. hole saws, has two speeds and Dual KickBack Control, and comes with two 6 Ah batteries. For holes past 5 in., Milwaukee’s 2811-20 is rated to 6 in.
Is there such a thing as a right angle drill?
Yes. Makers sell them as right angle drills, angle drills or stud and joist drills. The chuck sits at 90° to the body, so the drill fits between framing members.
How big a hole can I drill in a 2x4 stud?
Under IRC 2021 R602.6, up to 60% of the stud’s depth in a nonbearing wall: 2.10 in. in a 3-1/2 in. deep 2x4. In a bearing or exterior wall, holes over 40% (1.40 in.) need a doubled stud. Keep the edge of the hole at least 5/8 in. from the stud’s edge.
How big a hole can I drill in a floor joist?
Under IRC 2021 R502.8.1, up to one-third of a sawn joist’s depth, at least 2 in. from the top and bottom edges and from other holes. That’s 3.08 in. in a 2x10 and 3.75 in. in a 2x12. I-joists and trusses follow their maker’s rules.
What size hole do I need for 3 in. PVC?
Bigger than its 3.500 in. outside diameter, per Spears’ Schedule 40 sheet. That’s more than a 2x10 joist allows by code, so a 3 in. drain through a joist needs at least a 2x12, with a hole no bigger than 3.75 in.
Can I use a 1/2 in. drill bit in a 7/16 in. chuck?
Not a round 1/2 in. shank. The Bosch 127HX, Milwaukee and Makita chucks take 7/16 in. hex shank bits. DeWalt’s DCD446 has a 1/2 in. keyed chuck for round-shank bits.
How I picked these drills
Why trust me
I’m Isaac Daniels, I own Plain Buy Guides, and I edit this page. Every spec comes from the makers’ pages, the Amazon listings and the code books, read the same day, and where the documents disagree, the lower figure is the one listed.
How I pick
- Only genuine branded drills, new and in stock, re-checked through Amazon’s product data Oct 22, 2026, 5:53 PM EDT.
- Specs from the maker’s page, and from the Amazon listing where the maker’s page doesn’t give them. Gaps are marked “Not listed.”
- One spec score for all five drills, worked out below. Run-time claims use different bits, so the score only asks whether a figure is published.
- Code limits from IRC 2021, pipe sizes from Spears and the Copper Development Association, lumber sizes from NIST PS 20.
- CPSC recall search on Oct 19, 2026, repeated Oct 22, 2026, 5:54 PM EDT, found no recalls for these models.
- Prices are read from Amazon with the time shown, never typed in.
The spec score, check by check
Each check scores 0 to 10 and counts one fifth. It rewards a big hole rating, a kickback system, a length that fits between joists, a long warranty and a published run-time claim. The score is worked out from the makers’ figures, not a customer rating.
The Bosch and the Super Hawg tie at the top for different reasons: the Bosch has kickback control and fits the bay better, and the Super Hawg bores the biggest holes. The Bosch PS11 scores 6.4 on the same checks, which is why it sits in the left-out table.
| Check (weight) | How it’s scored |
|---|---|
| Hole size (⅕) | Largest hole the maker lists: 10 for 6 in. or more; 9 for a 5 in. hole saw; 8 for a 4 in. hole saw; 7 for 2-9/16 in. self-feed only; 3 for a 3/4 in. spade bit |
| Kickback (⅕) | 10 for an electronic kickback or anti-rotation system; 8 for a mechanical clutch; 6 for an electric brake only; 4 for none listed |
| Fits the bay (⅕) | Length, because a 16 in. joist bay leaves about 14-1/2 in.: 10 under 15 in.; 8 for 15 to 17 in.; 7 for 17 to 19 in.; 5 over 19 in. |
| Warranty (⅕) | Maker’s tool warranty: 10 for 5 years; 7 for 3 years; 4 when none is listed |
| Run time (⅕) | 10 when the maker or listing gives a holes-per-charge figure; 6 when none is given |
| Total | Average of the checks, to one decimal |
| Pick | Hole size | Kickback | Fits the bay | Warranty | Run time | Score |
|---|---|---|---|---|---|---|
| Bosch GRD18V-127HX | 9 | 10 | 8 | 10 | 6 | 8.6 |
| Milwaukee 2811-20 | 10 | 8 | 5 | 10 | 10 | 8.6 |
| Milwaukee 2808-20 | 8 | 4 | 8 | 10 | 10 | 8.0 |
| Makita XAD06Z | 9 | 6 | 7 | 7 | 10 | 7.8 |
| DeWalt DCD446B | 8 | 10 | 7 | 7 | 10 | 8.4 |
| Bosch PS11-102 (left out) | 3 | 6 | 10 | 7 | 6 | 6.4 |
Sources
- Bosch, GRD18V-127HXB26X 18V 7/16 In. High Torque Right Angle Drill Kit page (speeds, capacity, Dual KickBack Control, weight, size, contents): boschtools.com, read Oct 19, 2026.
- Bosch, PS11-102 12V Max 3/8 In. Angle Drill Kit page (weight, length, torque, speed, head, chuck, contents): boschtools.com, read Oct 19, 2026.
- Milwaukee, 2811-20 M18 FUEL Super Hawg and 2808-20 M18 FUEL Hole Hawg pages (holes, run time, chuck, speeds, weights, sizes, warranty): milwaukeetool.com, read Oct 19, 2026.
- Milwaukee, 2811-20 and 2808-20 operator’s manuals (58-14-0151d2 and 58-14-0421: gear speeds, self-feed and hole saw capacities): documents.milwaukeetool.com, read Nov 11, 2026.
- Makita, XAD06Z 18V LXT Brushless 7/16 in. Hex Right Angle Drill page (speeds, capacities, weight, length, brake, warranty): makitatools.com, read Oct 19, 2026.
- DeWalt, DCD446B 20V MAX XR Compact Stud & Joist Drill page (ANTI-ROTATION, capacity, run time, watts, speed, size, warranty): dewalt.com, read Oct 19, 2026.
- International Code Council, 2021 International Residential Code, R602.6, R602.6.1, R502.8.1 and R502.8.2: codes.iccsafe.org, read Oct 19, 2026.
- NIST, Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (dry dressed sizes): nist.gov, read Oct 19, 2026.
- Spears Manufacturing, Schedule 40 PVC Pipe Dimensions and Pressure Ratings (outside diameters): spearsmfg.com, read Oct 19, 2026.
- Copper Development Association, The Copper Tube Handbook (outside diameters, Type L table): copper.org, read Oct 19, 2026.
- U.S. Consumer Product Safety Commission recall database, searched by product and brand: saferproducts.gov, Oct 19, 2026. Re-searched Oct 22, 2026, 5:54 PM EDT (Bosch, Milwaukee, Makita, DeWalt): older hammer drill and cordless drill recalls only, none for these models.
- Amazon listings for all six drills (condition, stock, Bosch PS11 bit range and motor brake, Bosch warranty, Makita 7/8 in. hole count): read from Amazon’s own product data, Oct 19, 2026. Offers re-read Oct 22, 2026, 5:53 PM EDT: B0H3Q473YS, B07VYMTZPB, B08FVH5D13, B09FCPLJ3N, B0DJCV1BSG and B00BD5G3UC, all in stock. The Super Hawg pick changed from the tool-only offer to the 2811-22 kit on Nov 11, 2026; the kit offer was re-read Nov 11, 2026, 1:24 AM EST, in stock.
