Best digital torque wrenches

Five electronic torque wrenches scored on their makers’ own specs, with a checker for which one covers your torque spec.

As an Amazon Associate I earn from qualifying purchases.

On this page
  1. The picks
  2. TEKTON TRQ82123
  3. TEKTON TRQ81122
  4. GEARWRENCH 85195
  5. GEARWRENCH 85077
  6. GEARWRENCH 85076
  7. Torque spec checker
  8. Compare the picks
  9. Torque range
  10. Accuracy and standards
  11. Angle mode
  12. Head and ratchet
  13. Alerts and memory
  14. Calibration and warranty
  15. Left out
  16. Where sources disagree
  17. Recalls
  18. How to choose
  19. Questions
  20. How we pick

Quick answer

Our top pick is the TEKTON TRQ82123, a 1/2 in. drive electronic wrench rated 30 to 300 ft-lb with an angle mode and a serialized calibration certificate. For engine and smaller fasteners, get its 3/8 in. sibling, the TRQ81122. If you want the lightest wrench with angle mode and a 0.55 in. thick flex head, look at the GEARWRENCH 85195.

TEKTON TRQ82123 electronic torque wrench, black handle with a digital display and flex head
Best for big fasteners up to 300 ft-lb$395.00 at AmazonPrice as of Nov 16, 2026, 5:34 AM EST
Check it on Amazon

Five wrenches worth buying

All five were new and in stock on Amazon at our 6:21 PM check on Oct 26. Each is an electronic torque wrench with a ratchet head, scored on the same ten checks.

The five wrenches, card by card

Best for big fasteners up to 300 ft-lb

TEKTON TRQ82123

1/2 in. drive electronic torque wrench, 30–300 ft-lb

Model TRQ82123
$395.00
Check it on Amazon
in stock · price as of Nov 16, 2026, 5:34 AM EST
10Spec scoreHow it’s scored
Torque range10
Accuracy, both directions10
±2% or better both ways10
Angle mode10
Named standard10
Calibration certificate10
Light, sound and vibration10
Weight10
Length10
Recalibration path10

Pros

  • 30 to 300 ft-lb, the widest range here
  • ±2% in both directions, per TEKTON
  • Torque, angle, and torque plus angle modes
  • Serialized calibration certificate in the box
  • Length offset up to ±15 in. for crowfoot work

Cons

  • 4.51 lb, the heaviest pick
  • 27.1 in. long, so it needs room to swing
  • Needs 3 AA batteries, not included
  • Too big for small engine fasteners
Model TRQ821231/2 in. drive30–300 ft-lb90 teeth, 4° arcAngle 5–360°4.51 lb

Buy it if

Your specs run from 30 to 300 ft-lb and you want angle mode too.

Skip it if

Most of your specs are under 30 ft-lb. The TEKTON TRQ81122 starts at 10 ft-lb.

The TRQ82123 is TEKTON’s 1/2 in. drive electronic torque wrench, rated 30 to 300 ft-lb. It was new and in stock at our 6:21 PM check on Oct 26. It scores 10.0, meeting all ten checks, and wins the tie with its 3/8 in. sibling on range.

TEKTON states the torque accuracy as within ±2% clockwise and counterclockwise, and the angle accuracy as within ±1%. The GEARWRENCH and ACDelco pages quote ±3% counterclockwise; TEKTON quotes the same figure both ways, which matters if you torque left-hand threads.

It is calibrated to ISO 6789-1:2017, and TEKTON says it also meets ASME B107.300-2021. TEKTON’s page explains the difference: ISO tests the lowest marked value on the scale, asks for clockwise and counterclockwise to match, and takes five readings per set point, where ASME takes three.

In the box is a certificate of calibration with a serial number that matches the engraving on the wrench. TEKTON lists the torque test points for this model as 30, 180 and 300 ft-lb, tested five times each way, and the angle test points as 45°, 90°, 135° and 180°.

Three modes: torque, angle, and torque plus angle in one step. TEKTON says an onboard gyroscope lets the angle build up over several ratchet sweeps, so you don’t have to make the full turn in one pull.

Feedback comes four ways: the LCD, lights that change from yellow to green, beeps that turn to a continuous tone, and a vibrating handle. Sound and vibration can be switched off; the lights always stay on.

The length offset is the feature crowfoot users will notice. Enter up to ±15 in. (381 mm) of extension and the wrench does the torque conversion for you. It works in all three modes.

Other features from TEKTON’s page: 10 presets with repetition counters up to 99, a history of the last 50 peak readings, an over-torque warning past 110% of maximum, a calibration reminder by date or cycles, and an auto-shutoff you can set from 2 to 120 minutes.

It is a big tool: 27.1 in. overall, 22.8 in. effective length, 4.51 lb. A 1/2 to 3/8 in. reducer, a case and the manual come with it. TEKTON offers a recertification service for its electronic wrenches.

Our call: the wrench for big fasteners when you also want angle mode and a certificate. It scores 10.0.

Best for angle specs on a 3/8 in. drive

TEKTON TRQ81122

3/8 in. drive electronic torque wrench, 10–100 ft-lb

Model TRQ81122
$315.00
Check it on Amazon
in stock · price as of Nov 16, 2026, 5:34 AM EST
10Spec scoreHow it’s scored
Torque range10
Accuracy, both directions10
±2% or better both ways10
Angle mode10
Named standard10
Calibration certificate10
Light, sound and vibration10
Weight10
Length10
Recalibration path10

Pros

  • 10 to 100 ft-lb with ±2% both ways
  • Angle mode for torque-to-yield specs
  • Certificate tested at 10, 60 and 100 ft-lb
  • Comes with a 3/8 to 1/4 in. reducer
  • History of the last 50 peak readings

Cons

  • Not for specs above 100 ft-lb
  • 2.71 lb, heavier than the GEARWRENCH 3/8 in. wrenches
  • 20.0 in. long overall
  • Needs 3 AA batteries, not included
Model TRQ811223/8 in. drive10–100 ft-lb90 teeth, 4° arcAngle 5–360°2.71 lb

Buy it if

You work on engines, transmissions and brakes, with specs that call for torque then an added angle.

Skip it if

You need more than 100 ft-lb. The TEKTON TRQ82123 goes to 300 ft-lb.

The TRQ81122 is the 3/8 in. drive version of the same TEKTON wrench, rated 10 to 100 ft-lb. It was new and in stock at our 6:21 PM check on Oct 26. It scores 10.0 and places second only on the tie rule, because its range is narrower.

Accuracy matches the 1/2 in. model: within ±2% for torque in both directions and ±1% for angle. TEKTON notes that the actual accuracy for your wrench is printed on its certificate, and that the stated figure is the maximum allowed deviation.

Its certificate tests torque at 10, 60 and 100 ft-lb. That 10 ft-lb point is the bottom of the scale, which is the ISO rule TEKTON describes. If your specs sit near the low end, a tested low point is worth having.

Angle mode measures from 5° to 360°. TEKTON describes it for specs that tell you to turn a tightened fastener an additional amount; GEARWRENCH’s own FAQ ties angle settings to torque-to-yield work. Torque plus angle mode runs both steps without changing modes.

The ratchet has 90 teeth and a 4° swing arc. TEKTON says its single half-moon pawl keeps 10 teeth engaged with the gear at all times, so it won’t skip under stress. The 15° flex head helps you reach around obstructions.

Units are in-lb, ft-lb, Nm and kg-m. The display is a backlit LCD with large buttons, and there is a dedicated button for presets. Press and hold UNIT to see the last peak reading without opening the menus.

The length offset works up to ±15 in., the same as on the 1/2 in. model. That covers a crowfoot or torque adapter on the end of the drive, which changes the wrench’s effective length.

The wrench is 20.0 in. long overall, 15.9 in. effective, and weighs 2.71 lb. A case, the manual, the certificate and a 3/8 to 1/4 in. reducer come with it. Batteries are three AA cells you supply.

Our call: the 3/8 in. wrench for engine work and angle specs. It scores 10.0.

Best for tight engine bays

GEARWRENCH 85195

3/8 in. 120XP flex head electronic torque wrench with angle

Model 85195
$168.18
Check it on Amazon
low stock · price as of Nov 16, 2026, 5:34 AM EST
8.0Spec scoreHow it’s scored
Torque range10
Accuracy, both directions10
±2% or better both ways0
Angle mode10
Named standard10
Calibration certificate0
Light, sound and vibration10
Weight10
Length10
Recalibration path10

Pros

  • 120-tooth ratchet with a 3° arc, the finest here
  • 0.55 in. thick head, which flexes 15°
  • Angle from 5° to 999°, ±1% of reading
  • 1.8 lb, the lightest pick
  • 10 presets and a backlit display

Cons

  • ±3% counterclockwise, looser than TEKTON’s ±2%
  • No calibration certificate (GEARWRENCH lists Certified: No)
  • Calibration guaranteed for 90 days only
  • Tops out at 100 ft-lb
Model 851953/8 in. drive10–100 ft-lb120 teeth, 3° arcAngle 5–999°1.8 lb

Buy it if

You work in cramped engine bays and want angle mode in the lightest wrench here.

Skip it if

You torque left-hand threads often or want a certificate. The TEKTON TRQ81122 is ±2% both ways.

The 85195 is GEARWRENCH’s 3/8 in. 120XP flex head electronic wrench with angle, rated 10 to 100 ft-lb (120 to 1,200 in-lb). It was new and in stock at our 6:21 PM check on Oct 26. It scores 8.0.

Its head is built for tight spaces. GEARWRENCH lists a 120-tooth ratchet with a 3° swing arc, a 15° flex teardrop head, a low-profile tube and a flush on/off switch. The head is 0.55 in. thick, less than half the 1.25 in. of the fixed-head 85076.

GEARWRENCH states torque accuracy as ±2% clockwise and ±3% counterclockwise between 20% and 100% of the wrench’s capability. On a 10 to 100 ft-lb wrench, that band starts at 20 ft-lb. Angle accuracy is ±1% of reading.

That counterclockwise figure is the check it misses next to the TEKTON wrenches. It also misses the certificate check: GEARWRENCH’s spec table lists Certified: No. Those two are the gap between its 8.0 and TEKTON’s 10.0.

Three modes: peak torque, angle, and peak angle. Angle runs from 5° to 999°. GEARWRENCH’s FAQ says the angle can be preset for specific jobs, which it calls useful for torque-to-yield applications.

Alerts come from a vibrating handle, a buzzer and the LCD screen, and GEARWRENCH’s FAQ says the display is backlit. Readouts are in ft-lb, in-lb, Nm, kg-m and kg-cm. Ten presets store the settings you repeat.

The knurled aluminum handle has a marked midpoint, which GEARWRENCH says promotes accuracy. It lists ASME B107.10, B107.12, B107.28 and B107.300. The tool is 15.87 in. long and weighs 1.8 lb, and it ships in an injection-molded case with a foam insert.

GEARWRENCH’s warranty for torque products is one year, with calibration accuracy guaranteed for 90 days from receipt. Out of warranty, GEARWRENCH points you to its authorized repair centers in the US and Canada.

Our call: the lightest angle wrench here. It scores 8.0, held back by the counterclockwise figure and no certificate.

Best for a lighter 1/2 in. wrench

GEARWRENCH 85077

1/2 in. drive electronic torque wrench, 25–250 ft-lb

Model 85077
$176.00
Check it on Amazon
in stock · price as of Nov 16, 2026, 5:34 AM EST
7.0Spec scoreHow it’s scored
Torque range10
Accuracy, both directions10
±2% or better both ways0
Angle mode0
Named standard10
Calibration certificate0
Light, sound and vibration10
Weight10
Length10
Recalibration path10

Pros

  • 25 to 250 ft-lb on a 1/2 in. drive
  • 2.88 lb, lighter than the TEKTON 1/2 in.
  • Target Torque Alert warns as you approach the target
  • Oil and solvent resistant handle
  • Readings in 0.1 ft-lb steps

Cons

  • No angle mode
  • ±3% counterclockwise
  • Accuracy quoted from 50 ft-lb (20% of scale) up
  • Fixed head, 72 teeth
Model 850771/2 in. drive25–250 ft-lb72 teeth, 5° arcNo angle mode2.88 lb

Buy it if

You want a torque-only 1/2 in. electronic wrench for wheels and chassis work, lighter than the TEKTON.

Skip it if

Your specs call for an angle step. The TEKTON TRQ82123 has angle mode.

The 85077 is GEARWRENCH’s 1/2 in. drive electronic torque wrench, rated 25 to 250 ft-lb (34 to 340 Nm). It was new and in stock at our 6:21 PM check on Oct 26. It scores 7.0.

It is a torque-only wrench: no angle mode. GEARWRENCH lists five units (ft-lb, in-lb, Nm, kg-m, kg-cm) and 0.1 ft-lb increments on the primary scale.

Accuracy is ±2% clockwise and ±3% counterclockwise between 20% and 100% of the scale. On this wrench, 20% is 50 ft-lb. GEARWRENCH quotes no accuracy figure below that, so if a spec is between 25 and 50 ft-lb, the 3/8 in. wrenches are the better fit.

GEARWRENCH calls its alert Target Torque Alert: it warns as you approach the target, then a vibrating handle, buzzer and solid LED light tell you when you reach it.

The head is fixed, with a 72-tooth ratchet and a 5° swing arc. The head is 1.5 in. wide and 1.5 in. thick. GEARWRENCH says the handle and housing are oil and solvent resistant.

It is 25.75 in. long and weighs 2.88 lb, which is 1.63 lb less than the TEKTON 1/2 in. It meets or exceeds ASME B107.28M, per GEARWRENCH, and runs on three AAA batteries you supply. It comes in a blow-molded case.

GEARWRENCH lists the body as alloy steel with a full polish chrome finish and a 2.75 in. head length. The UPC on its page is 099575850776, which lets you match the box to the model before you open it.

GEARWRENCH’s warranty for torque products is one year, with calibration accuracy guaranteed for 90 days from receipt. Out of warranty, GEARWRENCH points you to its authorized repair centers in the US and Canada.

Our call: a lighter torque-only 1/2 in. wrench. It scores 7.0, held back by no angle mode, the counterclockwise figure and no certificate.

Best for a simple 3/8 in. torque-only wrench

GEARWRENCH 85076

3/8 in. drive electronic torque wrench, 10–100 ft-lb

Model 85076
$184.97
Check it on Amazon
in stock · price as of Nov 16, 2026, 5:34 AM EST
7.0Spec scoreHow it’s scored
Torque range10
Accuracy, both directions10
±2% or better both ways0
Angle mode0
Named standard10
Calibration certificate0
Light, sound and vibration10
Weight10
Length10
Recalibration path10

Pros

  • 10 to 100 ft-lb on a 3/8 in. drive
  • 1.98 lb and 15.75 in. long
  • Vibration, buzzer and LED alert
  • Five readout units
  • Oil and solvent resistant handle

Cons

  • No angle mode
  • ±3% counterclockwise
  • Accuracy quoted from 20 ft-lb up
  • Fixed head, 1.25 in. thick
Model 850763/8 in. drive10–100 ft-lb72 teeth, 5° arcNo angle mode1.98 lb

Buy it if

You want a straightforward electronic wrench for specs between 20 and 100 ft-lb, without angle or presets.

Skip it if

You need angle mode or a slimmer head. The GEARWRENCH 85195 has both.

The 85076 is the 3/8 in. version of the GEARWRENCH 85077, rated 10 to 100 ft-lb (13.5 to 135 Nm). It was new and in stock at our 6:21 PM check on Oct 26. It scores 7.0 and is last on the tie rule, with the narrowest range of the two 7.0 wrenches.

Accuracy is the same as its 1/2 in. sibling: ±2% clockwise and ±3% counterclockwise from 20% to 100% of scale. On this wrench that band is 20 to 100 ft-lb.

Like the 85077, it has GEARWRENCH’s Target Torque Alert: a warning as you approach the target, then the vibrating handle, buzzer and solid LED light. It reads in ft-lb, in-lb, Nm, kg-m and kg-cm, in 0.1 ft-lb steps.

The head is fixed, with a 72-tooth ratchet and a 5° arc. It is 1.25 in. wide and 1.25 in. thick, more than twice as thick as the 85195’s flex head. Where the head fits, this is a simpler tool with fewer menus.

It is 15.75 in. long and weighs 1.98 lb. GEARWRENCH lists ASME B107.28M and a blow-molded case. It runs on three AAA batteries, not included.

GEARWRENCH lists alloy steel with a full polish chrome finish and a 2.4 in. head length. Its UPC is 099575850769; match it against the box so you know you have the 85076 and not a look-alike.

Its Amazon title reads 7.4 to 99.6 ft-lb, while GEARWRENCH’s page lists 10 to 100 ft-lb. We use GEARWRENCH’s figure, and we list the gap in the table of disagreements.

GEARWRENCH’s warranty for torque products is one year, with calibration accuracy guaranteed for 90 days from receipt. Out of warranty, GEARWRENCH points you to its authorized repair centers in the US and Canada.

Our call: the simplest wrench here for 3/8 in. work. It scores 7.0.

Which wrench fits your spec

Type the torque your service manual gives, in ft-lb or Nm. The checker compares it with each wrench’s published range and accuracy band.

Torque spec checker

Type the torque from your service manual and pick the unit.

Type your torque spec to check each wrench.

Ranges and accuracy bands from TEKTON’s and GEARWRENCH’s product pages, read Oct 26, 2026. The checker does arithmetic only.

The checker does arithmetic with the makers’ numbers only. GEARWRENCH quotes its accuracy from 20% to 100% of each wrench’s scale, so a spec inside the range but under 20% shows as “in range, below the quoted accuracy band”. TEKTON says its wrenches are calibrated across the full range, from the lowest marked value up, so any spec inside the range is inside its band.

Newton-metres are converted at 1 ft-lb = 1.3558 Nm. Always take the spec from the service manual for your vehicle or machine, not from a chart on a forum.

The five wrenches compared

From the makers’ product pages. Scroll sideways on a phone; tap a header to sort on a computer.

TEKTON TRQ8212310TEKTON TRQ8112210GEARWRENCH 851958.0GEARWRENCH 850777.0GEARWRENCH 850767.0010TEKTON TRQ8212310TEKTON TRQ8112210GEARWRENCH 851958.0GEARWRENCH 850777.0GEARWRENCH 850767.0
Plain Buy Guides spec score out of 10. Ten published facts, one point each; it’s our arithmetic, not a customer rating.
WrenchSpec scoreDriveRange (ft-lb)AccuracyRatchetHeadAngleWeight (lb)Buy
TEKTON TRQ8212310.01/2 in.30–300±2% CW and CCW90 / 4°15° flex5–360°4.51Check it on Amazon
TEKTON TRQ8112210.03/8 in.10–100±2% CW and CCW90 / 4°15° flex5–360°2.71Check it on Amazon
GEARWRENCH 851958.03/8 in.10–100±2% CW, ±3% CCW120 / 3°15° flex5–999°1.8Check it on Amazon
GEARWRENCH 850777.01/2 in.25–250±2% CW, ±3% CCW72 / 5°FixedNone2.88Check it on Amazon
GEARWRENCH 850767.03/8 in.10–100±2% CW, ±3% CCW72 / 5°FixedNone1.98Check it on Amazon

Why only TEKTON and GEARWRENCH: of the electronic torque wrenches we found new and in stock on Amazon on Oct 26, these two makers publish accuracy in both directions, the standard they meet, weight, length and a route to recalibration. DEWALT, CRAFTSMAN and ACDelco are in the left-out table with their scores.

Pick the range first

A torque wrench is only useful inside its range. Drive size and range go together on every pick here.

TEKTON TRQ8212330–300 ft-lbTEKTON TRQ8112210–100 ft-lbGEARWRENCH 8519510–100 ft-lbGEARWRENCH 8507725–250 ft-lbGEARWRENCH 8507610–100 ft-lbTEKTON TRQ8212330–300 ft-lbTEKTON TRQ8112210–100 ft-lbGEARWRENCH 8519510–100 ft-lbGEARWRENCH 8507725–250 ft-lbGEARWRENCH 8507610–100 ft-lb
Published torque range from each maker’s page. Bars show the top of the range.
DriveWrenchRange (ft-lb)Range (Nm)Quoted accuracy band (ft-lb)
1/2 in.TEKTON TRQ8212330–300≈41–40730–300 (full range)
1/2 in.GEARWRENCH 8507725–25034–34050–250 (20–100% of scale)
3/8 in.TEKTON TRQ8112210–100≈14–13610–100 (full range)
3/8 in.GEARWRENCH 8519510–10013.5–13520–100 (20–100% of scale)
3/8 in.GEARWRENCH 8507610–10013.5–13520–100 (20–100% of scale)

The Nm figures for GEARWRENCH are from its spec tables; for TEKTON we converted the ft-lb range, marked ≈. Neither maker sells a 1/4 in. drive pick here: GEARWRENCH’s 1/4 in. 85194 was in stock but we didn’t score it, because a 1/4 in. wrench covers a different set of jobs from these five.

A simple rule from the numbers: 3/8 in. wrenches here cover 10 to 100 ft-lb, and 1/2 in. wrenches cover 25 or 30 ft-lb up to 250 or 300. If your specs span both, two wrenches beat one stretched across a range it wasn’t built for. For lug nuts specifically, our torque wrench for lug nuts guide compares click and beam wrenches too.

Accuracy and standards

Every pick publishes an accuracy figure. They differ in the counterclockwise number and the standard they test to.

WrenchClockwiseCounterclockwiseAngleStandard named
TEKTON TRQ82123±2%±2%±1%ISO 6789-1:2017, ASME B107.300-2021
TEKTON TRQ81122±2%±2%±1%ISO 6789-1:2017, ASME B107.300-2021
GEARWRENCH 85195±2%±3%±1% of readingASME B107.10, B107.12, B107.28, B107.300
GEARWRENCH 85077±2%±3%NoneASME B107.28M
GEARWRENCH 85076±2%±3%NoneASME B107.28M

Counterclockwise accuracy matters when you tighten left-hand threads; your service manual says which fasteners are left-hand. If you never torque counterclockwise, the counterclockwise figure doesn’t come into play.

TEKTON’s page sets out how ISO 6789 differs from ASME in three ways. ISO tests the lowest marked value on the scale, while ASME starts at 20% of the range. ISO requires clockwise and counterclockwise results to match. ISO takes five readings at each set point, ASME three. TEKTON says that because its wrenches are calibrated to ISO, they also meet ASME.

None of this is a lab test of ours. It is what each maker publishes, and our score only counts whether they publish it and whether the figure is ±2% or better both ways.

Angle mode, and when you need it

Some fastener specs give a torque, then an extra turn in degrees. A wrench with angle mode measures that turn for you.

WrenchAngle rangeModes
TEKTON TRQ821235–360°Torque; angle; torque plus angle
TEKTON TRQ811225–360°Torque; angle; torque plus angle
GEARWRENCH 851955–999°Peak torque; angle; peak angle
GEARWRENCH 85077NoneTorque
GEARWRENCH 85076NoneTorque

TEKTON describes angle mode for specs that prescribe turning a tightened fastener an additional amount to reach the final clamping force. GEARWRENCH’s FAQ calls angle presets especially useful for torque-to-yield applications.

Both makers’ angle wrenches let you work in more than one sweep. TEKTON says an onboard gyroscope adds up the angle as you ratchet, so you can make a 90° turn as several small pulls where the handle has no room to swing. If none of your manuals list an angle step, a torque-only wrench such as the GEARWRENCH 85077 or 85076 does the job with fewer menus.

GEARWRENCH 851953°TEKTON TRQ821234°TEKTON TRQ811224°GEARWRENCH 850775°GEARWRENCH 850765°GEARWRENCH 851953°TEKTON TRQ821234°TEKTON TRQ811224°GEARWRENCH 850775°GEARWRENCH 850765°
Ratchet swing arc from each maker’s page.

The GEARWRENCH 85195 has the finest ratchet here, 120 teeth and 3°, and a 0.55 in. thick head that flexes 15°. TEKTON doesn’t publish a head thickness, so we can’t compare it on that. Both TEKTON wrenches use 90 teeth, a 4° arc and a 15° flex head, and TEKTON says the single half-moon pawl keeps 10 teeth engaged at all times.

The GEARWRENCH 85077 and 85076 have fixed heads with 72 teeth and a 5° arc. Their heads are 1.5 and 1.25 in. thick. GEARWRENCH says the 85195’s low-profile tube, flex head and flush switch give better access in tight confines; the fixed-head pair has none of those.

Alerts, presets and memory

All five tell you when you hit the target in more than one way. The extras differ.

FeatureTEKTON TRQ82123 / TRQ81122GEARWRENCH 85195GEARWRENCH 85077 / 85076
Target alertLCD, lights yellow to green, beeps, vibrationVibrating handle, buzzer, LCDWarning as you approach; vibration, buzzer, solid LED
Presets10, with repetition counters up to 9910Not listed
HistoryLast 50 peak readingsNot listedNot listed
Length offsetUp to ±15 in. / 381 mmNot listedNot listed
Calibration reminderBy date or cycle countNot listedNot listed
Over-torque warningPast 110% of maximum, loggedNot listedNot listed
Batteries3 AA, not includedAA (count not listed), not included3 AAA, not included

“Not listed” means the maker’s page doesn’t mention it; it isn’t a claim the wrench lacks it. Our score doesn’t count presets or memory; it counts accuracy, standards and the other checks in the method box below.

Calibration, certificates and warranty

GEARWRENCH says torque products should be routinely checked for calibration. What matters is what the maker gives you on day one and how you get it checked later.

MakerIn the boxCalibration termsLater service
TEKTONSerialized certificate of calibrationActual accuracy printed on your certificateTEKTON recertification service
GEARWRENCHNo certificate (Certified: No)Accuracy guaranteed for 90 days from receipt; 1 year on partsAuthorized repair centers in the US and Canada

GEARWRENCH’s warranty page says its torque products contain moving parts subject to normal wear, that service and replacement are the buyer’s responsibility, and that they should be routinely checked for calibration. Its US torque wrench service center is Angle Repair & Calibration Service in Beckley, West Virginia.

TEKTON’s wrenches can remind you to recalibrate by a date or a number of cycles you set. TEKTON doesn’t publish a recalibration interval on these pages, and neither does GEARWRENCH, so set one that suits how often you use the wrench.

The wrenches we checked and left out

All new and in stock on Amazon on Oct 26, and scored on the same ten checks.

Wrench checkedScoreWhy it isn’t a pick
ACDelco ARM601‑4, 1/2 in., 14.8–147.5 ft-lb4.0ACDelco’s page gives ±2% CW and ±3% CCW, length and weight, but no angle mode, no named standard and a buzzer-only alert
DEWALT DWMT17061, 3/8 in., 20–100 ft-lb2.0DEWALT’s page lists the range and a 20.3 in. length, but no accuracy figure, standard, weight or calibration terms
CRAFTSMAN CMMT99436, 1/2 in.0.0CRAFTSMAN’s page lists a 250 ft-lb maximum only, and calls the wrench “click style”; no accuracy, standard or weight

These are real tools from known makers. They score lower because their makers’ own pages leave out the facts our checks need, not because we found a fault. If DEWALT or CRAFTSMAN publish accuracy figures later, we’ll rescore them. The ACDelco Amazon title mentions ISO 6789 and an LED flash; ACDelco’s own page says neither, so we score what ACDelco publishes.

Where the sources disagree

Where the makers’ pages and the Amazon listings say different things.

TopicMaker saysListing saysWe use
GEARWRENCH 85076 range10–100 ft-lb7.4–99.6 ft-lbThe maker’s page
ACDelco ARM601‑4 standardNo standard namedISO 6789 in the titleThe maker’s page
ACDelco ARM601‑4 alertBuzzerBuzzer and LED flashThe maker’s page
CRAFTSMAN CMMT99436 range250 ft-lb maximum50–250 ft-lbThe maker’s page (left out)

Recalls

We searched the CPSC recall list on Oct 26, 2026.

SearchRecalls found
Torque wrenchNone
TEKTONNone
GEARWRENCHNone

How to choose a digital torque wrench

Answer these in order. Each answer narrows the picks.

QuestionIf yesIf no
Do most of your specs sit above 100 ft-lb?A 1/2 in. wrench: next questionA 3/8 in. wrench: skip to question 3
Do you need angle mode or a certificate?TEKTON TRQ82123GEARWRENCH 85077 (lighter)
Do you need angle mode or a certificate at 3/8 in.?TEKTON TRQ81122, or GEARWRENCH 85195 for the lightestGEARWRENCH 85076
Are your specs under 20 ft-lb?TEKTON TRQ81122 (accuracy quoted from 10 ft-lb)Any 3/8 in. pick fits

Range comes first because it rules wrenches in or out. Then decide on angle mode: if your manuals give torque plus degrees, buy a wrench that measures the angle. Last, weigh head size against features. A good tool bag keeps the case and sockets together, and a fresh car battery is worth checking while the wheels are off.

Questions people ask

Do digital torque wrenches need to be calibrated?

Yes. GEARWRENCH says its torque products should be routinely checked for calibration and guarantees calibration for 90 days. TEKTON ships each wrench with a certificate, offers recertification and lets you set a reminder by date or cycles.

Are digital torque wrenches more accurate than click wrenches?

Our picks publish ±2% clockwise; TEKTON also quotes ±2% counterclockwise. Compare that with the figure printed for any click wrench you’re considering. Our score counts what the maker publishes.

How does a digital torque wrench work?

It measures the resistance to rotation as you tighten, in TEKTON’s words, and shows it on a display. When you reach the target you set, it signals with lights, a sound and a vibrating handle.

How do you use a digital torque wrench?

Turn it on, choose the mode and unit, set the target from your service manual, then pull smoothly until it signals. TEKTON’s and GEARWRENCH’s manuals give the full steps for each model.

What is angle mode for?

Specs that give a torque and then an extra turn in degrees. TEKTON’s torque plus angle mode does both steps without changing modes; GEARWRENCH’s 85195 has angle and peak angle modes.

What drive size do I need?

Here, 3/8 in. wrenches cover 10 to 100 ft-lb and 1/2 in. wrenches cover 25 or 30 up to 250 or 300 ft-lb. Match the drive to the range your specs need.

Can I use a crowfoot with a digital torque wrench?

Yes, but it changes the effective length. TEKTON’s length offset lets you enter up to ±15 in. and the wrench converts the reading for you.

Do these wrenches come with batteries?

No. The TEKTON wrenches need 3 AA cells, the GEARWRENCH 85195 takes AA, and the 85077 and 85076 need 3 AAA. None includes them.

What warranty do they have?

GEARWRENCH: one year on parts and 90 days on calibration accuracy. TEKTON’s pages point to its recertification service; check its warranty page for current terms.

Why are the picks only TEKTON and GEARWRENCH?

They were the makers whose own pages published accuracy both ways, a named standard, weight, length and a recalibration path for wrenches in stock on Amazon on Oct 26. ACDelco, DEWALT and CRAFTSMAN are in the left-out table.

How much does a digital torque wrench cost?

Prices change, so each card shows today’s Amazon price with the time we read it. Our scores don’t use price.

How we pick digital torque wrenches

How we pick

This page compares electronic torque wrenches only: a ratchet head that measures torque and shows it on a digital readout. Each listing was read on Amazon at 6:21 PM on Oct 26, 2026, and had to be new, in stock and winning the buy box. Any Amazon seller qualifies.

The score adds up ten yes-or-no checks taken from each maker’s own pages. If the maker doesn’t publish it, the check gets no point. When two wrenches tie, the one with the wider torque range goes first.

Why trust us

Isaac Daniels, who owns Plain Buy Guides, edits this page. We read TEKTON’s, GEARWRENCH’s, DEWALT’s, CRAFTSMAN’s and ACDelco’s product pages, GEARWRENCH’s and TEKTON’s warranty pages and the CPSC recall list, all on Oct 26, 2026.

The ten checks, part one: the maker publishes the torque range; accuracy in both directions; a figure of ±2% or better both ways; an angle mode; and a named standard such as ISO 6789 or ASME B107.

Part two: a calibration certificate in the box; a target alert by light, sound and vibration; the weight; the length; and a published recalibration or repair route.

The spec score, check by check

WrenchTorque rangeAccuracy, both directions±2% or better both waysAngle modeNamed standardCalibration certificateLight, sound and vibrationWeightLengthRecalibration pathScore
TEKTON TRQ82123111111111110.0
TEKTON TRQ81122111111111110.0
GEARWRENCH 8519511011011118.0
GEARWRENCH 8507711001011117.0
GEARWRENCH 8507611001011117.0
ACDelco ARM601‑411000001104.0
DEWALT DWMT1706110000000102.0
CRAFTSMAN CMMT9943600000000000.0

Sources

  • TEKTON (tekton.com), product pages for TRQ81122 and TRQ82123, and its warranty and recertification pages
  • GEARWRENCH (gearwrench.com), product pages for 85076, 85077 and 85195, and its warranty page
  • DEWALT (dewalt.com), DWMT17061 product page
  • CRAFTSMAN (craftsman.com), CMMT99436 product page
  • ACDelco Tools (acdelcotools.com), ARM601‑4 product page
  • U.S. Consumer Product Safety Commission recall API, searched Oct 26, 2026
  • US keyword and SERP data for digital torque wrench, pulled Oct 26, 2026
  • Amazon offer read, Oct 26, 2026, 6:21 PM EDT

Related guides