Updated Oct 22, 2026 · New picks and spec scores; a blank-fit checker, capacity and speed charts, and motor, indexing, extension and warranty sections added
As an Amazon Associate I earn from qualifying purchases.
Our top pick is the JET JWL-1221VS: a 1 HP motor, speeds down to 60 RPM, 24 index stops and a five-year warranty. Get the WEN 34035 for bowls up to 14 in., or the Rockler VS 12-24 for spindles up to 24 in.
Best for bowls and spindles alike$989.99 at AmazonPrice as of Nov 16, 2026, 5:34 AM EST · low stock then
All five were new and in stock at our 7:45 AM check on Oct 22. Each is a 120 V variable-speed midi lathe with a 12 to 14 in. swing, scored on the same eight checks.
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
The five lathes, card by card
Best for bowls and spindles alike
JET JWL-1221VS
12 x 21 in. 1 HP Variable-Speed Wood Lathe, 719200
71920012-1/2 in. swing20-1/4 in. centers1 HP60–3,600 RPM24 index stops
Buy it if
You want one lathe that handles a wet bowl blank and a long table leg, backed by a long warranty.
Skip it if
You mostly turn bowls wider than 12 in. The WEN 34035 swings 14 in. over the bed.
The JWL-1221VS is our top pick and the highest score on the page. It was new and in stock at our 7:45 AM check on Oct 22, sold by Amazon.com, with only 2 left. The listing names model 719200, which JET’s spec table gives as the old material number for the JWL-1221VS.
Capacity is the all-round kind. JET lists a 12-1/2 in. swing over the bed and 20-1/4 in. between centers. Over the bed it clears a blank up to 12-1/2 in. across, and between centers it takes work up to 20-1/4 in. long, such as a short table leg or a pair of candlesticks.
Speed is where it pulls ahead. Three belt positions give 60 to 900, 110 to 1,800 and 220 to 3,600 RPM. That 60 RPM floor is the second lowest here, behind only the Laguna’s 50. The Laguna, NOVA, Rockler and WEN manuals all say to start a new blank slowly, and a slow start helps most on an out-of-round bowl blank.
The motor is a 1 HP induction drive on 115 V, drawing 6 A, and JET recommends a 10 A circuit. JET calls it continuous duty. The listing describes a ratchet-style belt tension system and a larger digital readout with a recessed power switch.
The listing also says forward to reverse is a smooth transition. JET’s own spec table doesn’t mention reverse, so we score it from the listing. Reverse is mainly for sanding, which leaves fewer swirl marks when you sand both ways.
There are 24 indexing positions with a spring-loaded spindle lock, per the listing. That lets you mark evenly spaced flutes, beads or holes, 15° apart. The headstock slides along the bed, and the spindle is 1 in. by 8 TPI with a Morse taper 2 (MT2) socket, so most chucks and centers fit.
JET includes two tool rests, 6 and 10 in. long on a 5/8 in. post. Its spec table lists 2-1/4 in. of quill travel, a 3/8 in. spindle bore and steady rest capacity of 0.2 to 3.5 in. JET sells a 22-inch bed extension for longer work, though it doesn’t state the length it adds between centers.
JET backs it with a five-year warranty, the longest stated here. Our call: the best all-round midi lathe on this page. It scores 9.7, held back only by its 12-1/2 in. swing against the WEN’s 14 in.
MLAREVO1216EVS12-1/2 in. swing15-1/2 in. centers1 HP DC50–3,500 RPM118 lb
Buy it if
You turn bowls and want to grow into 16 in. platters later without buying a bigger lathe.
Skip it if
You turn long spindles. The Rockler takes 24 in. between centers as sold.
The REVO 12|16 is the bowl turner’s pick. It was new and in stock at our 7:45 AM check on Oct 22, sold by Amazon.com, with only 3 left. The listing names model MLAREVO1216EVS, the model in Laguna’s manual.
Its motor is the story. Laguna fits a 1 HP permanent-magnet DC motor with a pulse width modulation (PWM) controller. Laguna says cheaper controllers cut torque along with speed, and that this is why many midi lathes start at 250 RPM or higher. It says PWM keeps full torque across the whole range.
That shows in the speeds. Three belt groups give 50 to 525, 325 to 1,750 and 650 to 3,500 RPM, so its 50 RPM floor is the lowest on this page. The belt is a 6-groove Poly-V, and a cam handle releases the tension when you move it between pulleys.
As sold, it swings 12-1/2 in. over the bed and 9-1/2 in. over the banjo, with 15-1/2 in. between centers. That’s the shortest bed here, and why it trails the JET. Laguna’s 10 in. expansion set mounts on either end. On the tailstock end it takes centers to 25-1/2 in.
On the headstock end, the same set turns it into an outboard lathe. The spindle is threaded 1 in. by 8 TPI on both ends, so a chuck can go on the back, and Laguna gives 16 in. as the maximum outboard swing. The manual says you must use a reversible chuck with set screws for outboard work.
Reverse rotation is standard, per the manual, and the control panel has a digital readout. There are 24 indexing positions with a lock. Laguna lists 2-1/2 in. of quill travel, an 8 in. tool rest on a 1 in. post and a 3 in. faceplate. It’s CSA certified and asks for a 15 A breaker.
It weighs 118 lb net and measures about 35.8 by 14.6 by 20.5 in. Laguna also sells a 20 in. bed extension, an adjustable stand and a wheel system. The pages and manual we read register the warranty but don’t give its length, so it isn’t in the warranty table as a number.
Our call: the lathe for bowls now and big platters later. It scores 9.5, held back only by its 15-1/2 in. bed as sold.
Best for the widest swing
WEN 34035
6-Amp 14 x 20 in. Variable-Speed Benchtop Wood Lathe
3403514 in. swing20 in. centers6 A, 120 V250–3,550 RPM125.7 lb
Buy it if
You want the most bowl diameter on a benchtop lathe, plus 20 in. for spindles.
Skip it if
You rough out lopsided blanks. The JET starts at 60 RPM and the Laguna at 50.
The WEN 34035 has the most room for bowls on this page. It was new and in stock at our 7:45 AM check on Oct 22, sold by Amazon.com. The listing and WEN’s manual both name model 34035.
WEN’s manual lists a 14 in. swing over the bed and 20 in. between centers, with a 7 in. center height. That 14 in. is the widest swing here, an inch and a half more than the JET or the Laguna. It’s the reason the WEN scores full marks on swing, which counts double.
The motor is listed as 120 V, 60 Hz and 6 A. WEN doesn’t give horsepower anywhere we read, so it scores 6 on our motor check, which also counts double. That’s the main reason it sits third, not first.
Three belt positions give 250 to 720, 600 to 1,700 and 1,200 to 3,550 RPM, and a digital RPM readout shows the speed. WEN’s manual says to start rough cuts and larger blanks at slower speeds. A 250 RPM floor is fine for most blanks you’ve cut round on a band saw, but slower than the JET or Laguna for lopsided ones.
The manual names a direction switch and says not to change direction while the lathe is on. If you do, the display shows error F3 and you restart. There are 24 index positions in the spindle pulley, each 15° apart, and a spindle lock to hold one.
The tailstock has 3-1/2 in. of quill travel, the longest any maker here states, which helps when you drill down the center of a vase or a lamp. The spindle is 1 in. by 8 TPI with MT2 tapers at both ends.
The 4 in. faceplate beats the 3 in. ones Laguna, Rockler and NOVA include, and you also get an 8 in. tool rest, a spur center and a live center.
It weighs 125.7 lb and measures 38 by 11.8 by 22.6 in. WEN’s product page says that 120-plus pound build prevents walking and wobbling. WEN sells an extension bed, 34035EX, and a stand, LA8800, but doesn’t state the extended length. The warranty is two years.
Our call: the benchtop lathe for the biggest bowls. It scores 8.9, held back by an unstated horsepower and a 250 RPM floor.
#7233312 in. swing24 in. centers1.2 HP300–3,500 RPM93 lb boxed
Buy it if
You turn chair spindles, table legs or tool handles and want room to grow to 54 in.
Skip it if
You plan fluted or evenly spaced work. The JET and WEN have 24 index stops.
The VS 12-24 is the spindle turner’s pick. It was new and in stock at our 7:45 AM check on Oct 22, sold by Rockler Woodworking and Hardware, Rockler’s own store on Amazon, with 9 left. The listing names model 72333, Rockler’s item number.
Its name gives its capacity: 12 in. over the bed and 24 in. between centers. That 24 in. is the most between centers of any pick as sold. With Rockler’s bed extension, item 71801, Rockler says spindle capacity grows to 54 in., long enough for most table legs and bedposts.
Rockler rates the motor at 1.2 HP on 120 V, the biggest figure on this page. The bed, headstock and tailstock are all cast iron, which Rockler says cuts vibration. The box weighs 93 lb with packaging, and Rockler gives a footprint of 7-1/4 by 34-3/4 in. and a working space of 16 by 45 in.
Speed comes in two belt ranges, not three. Rockler’s product page gives 300 to 1,100 and 750 to 3,500 RPM, and a knob sets the speed while the digital readout shows it. The manual prints the low range as 300 to 1,400 RPM. The floor is 300 either way, the highest of the five, and it scores 7 on lowest speed.
A switch flips the spindle from forward to reverse. The manual is firm that reverse is for sanding only, never for cutting with gouges or chisels. It says to switch with the lathe off and the belt on the low range, and to stop often when you sand in reverse so a chuck doesn’t unthread.
Rockler’s page and manual don’t mention indexing, so it scores 4 on that check. That’s the main reason it trails the WEN. If you want to lay out flutes or evenly spaced holes, you’d have to mark them by hand.
In the box are a spur center, a live center, a 3 in. faceplate, a 7-7/8 in. tool rest on a 5/8 in. post and a plastic spindle washer. Rockler says the washer helps stop faceplates and chucks sticking on the spindle. A stand, item 72011, and a stand extension, item 73441, are sold separately.
Our call: the lathe for long, thin work. It scores 8.7, held back by no stated indexing and a 300 RPM floor.
Best for pens and small work
NOVA Comet II DR
Midi Wood Lathe, 3/4 HP DC, Forward and Reverse, 46303
12 in. swing16-1/2 in. centers3/4 HP DC250–4,000 RPM12 index stops84 lb
Buy it if
You turn pens, ornaments, bottle stoppers and small bowls, and want a lathe you can lift.
Skip it if
You rough out big, wet bowl blanks. The Laguna has more motor and a 50 RPM floor.
The Comet II DR is the small-work pick. It was new and in stock at our 7:45 AM check on Oct 22, sold by NOVA Woodworking, NOVA’s own store on Amazon, with only 2 left. The listing describes NOVA’s Comet II DR with its 250 to 4,000 RPM range and display screen.
Its top speed is the highest on this page. Three pulleys give 250 to 680, 530 to 1,420 and 1,380 to 4,000 RPM. NOVA’s manual matches each band to a kind of work: the slow band for large faceplate and spindle work, the fast band for small and miniature turning. Pens and finials want the fast band.
The motor is a 3/4 HP permanent-magnet DC motor, 550 watts, which NOVA says can put out more than its rating. That 3/4 HP is the smallest rating here, so it scores 8 on motor. A dial sets the speed and a display shows it; NOVA’s manual says to start at about a quarter of the range and avoid sudden jumps from low to high.
A switch changes the direction for sanding. The spindle index has 12 notches, 30° apart, per the manual. That’s half the JET’s, Laguna’s and WEN’s 24, so it scores 7 on indexing. You can still split work into 2, 3, 4, 6 or 12 even parts.
Capacity is 12 in. over the bed and 16-1/2 in. between centers. NOVA sells a cast-iron bed extension, 47015, and its product page says the bed is extendable to 42 in. with it. The manual says each extension adds 24.6 in., while the Amazon listing says 25.6 in.; we show both in the conflicts table.
The spindle is 1 in. by 8 TPI with an MT2 taper and a 3/8 in. hole through it. The tailstock is self-ejecting. NOVA’s page gives 1.6 in. of quill travel and the manual 2 in. The tool rest is 6 in. and the faceplate 3 in.
NOVA’s page lists 84 lb, and its manual 77.2 lb packaged, against Rockler’s 93 lb with packaging, so it’s the lightest lathe here. The warranty, per NOVA’s page, is 1 year on the motor and controller and 2 years on mechanical parts. A matching stand, 47050, and stand extension, 47051, are sold separately.
Our call: the lathe for pens and small pieces that may move off the bench. It scores 8.5, held back by its 3/4 HP motor and 12 index stops.
Will your blank fit?
Pick the widest bowl and the longest spindle you plan to turn. The checker uses each maker’s stated capacity.
Blank-fit checker
Every pick is a benchtop midi lathe. Choose a size to see which ones take it.
Over the bed: JET JWL-1221VS, Laguna REVO 12|16, WEN 34035, Rockler VS 12-24, NOVA Comet II DR.
As sold: JET JWL-1221VS, WEN 34035, Rockler VS 12-24. With the maker’s bed extension: Laguna REVO 12|16, NOVA Comet II DR.
Capacities as stated by JET, Laguna, WEN, Rockler and NOVA, read Oct 22, 2026. Leave room for the tool rest.
Swing over the bed is the largest diameter that clears the bed. Over the tool rest base, called the banjo, it’s less: Laguna gives 9-1/2 in. over the banjo on the REVO. Plan bowls an inch or two under the full swing so the tool rest can reach the rim.
The five lathes compared
From the makers’ spec sheets and manuals. Scroll sideways on a phone; tap a header to sort on a computer.
Plain Buy Guides spec score out of 10: JET JWL-1221VS, Laguna REVO 12|16, WEN 34035, Rockler VS 12-24 and NOVA Comet II DR. Built from eight published specs; it’s our arithmetic, not a customer rating.
All five take 1 in. by 8 TPI chucks and MT2 centers, all have a digital speed readout, and all reverse. They differ most on swing, bed length, motor and how slowly they can start.
How much each lathe can hold
Each lathe’s swing and length between centers, drawn at one scale from its maker’s figures.
Sources: JET spec table, Laguna product page, WEN manual, Rockler product page and NOVA manual, read Oct 22, 2026. Capacity as sold, without bed extensions.
Lathe
Swing over bed
Between centers
With the maker’s extension
JET JWL-1221VS
12-1/2 in.
20-1/4 in.
22-inch bed extension sold; added length not stated
Laguna REVO 12|16
12-1/2 in. (9-1/2 in. over the banjo)
15-1/2 in.
25-1/2 in. with the 10 in. expansion set; 16 in. outboard
WEN 34035
14 in.
20 in.
Extension bed 34035EX sold; length not stated
Rockler VS 12-24
12 in.
24 in.
54 in. with bed extension 71801
NOVA Comet II DR
12 in.
16-1/2 in.
About 42 in. with bed extension 47015
Swing is twice the height from the bed to the spindle center. WEN gives that center height as 7 in., which is where its 14 in. swing comes from. A 12 in. swing doesn’t mean a 12 in. bowl, though: the banjo and tool rest sit under the work, and a blank needs clearance as it wobbles before it’s round.
Between centers is the longest spindle you can mount from the drive center to the tailstock. Bowls don’t use it. Swing counts double in our score because no extension adds swing over the bed; length you can add later.
How slow and how fast each lathe turns
Each lathe changes range by moving a belt, then fine-tunes with a knob. Here are the ranges on one RPM scale.
Belt ranges from the JET spec table, Laguna product page, WEN manual, Rockler product page and NOVA manual, read Oct 22, 2026. Rockler’s manual prints its low range as 300 to 1,400 RPM.
Lathe
Low belt
Middle belt
High belt
Readout
JET JWL-1221VS
60–900 RPM
110–1,800 RPM
220–3,600 RPM
Digital
Laguna REVO 12|16
50–525 RPM
325–1,750 RPM
650–3,500 RPM
Digital
WEN 34035
250–720 RPM
600–1,700 RPM
1,200–3,550 RPM
Digital
Rockler VS 12-24
300–1,100 RPM
None
750–3,500 RPM
Digital
NOVA Comet II DR
250–680 RPM
530–1,420 RPM
1,380–4,000 RPM
Digital
Why does the low end matter? The Laguna, NOVA, Rockler and WEN manuals all say to start a new or unbalanced piece slowly. Rockler’s puts it plainly: the larger the diameter, the slower the speed. A blank that’s heavier on one side shakes the lathe at speed, and a 50 or 60 RPM start lets you true it gently.
The top end matters less on a midi lathe. Every pick reaches 3,500 RPM or more, which is plenty for pens and small spindles. NOVA’s 4,000 RPM is the highest. Belt changes take a minute, so three ranges mean you move the belt less often than with two.
Motor power and drive type
Motor counts double in our score, because a stalled cut on a big blank is where a small lathe gives up.
Lathe
Motor as stated
Type
Circuit
JET JWL-1221VS
1 HP, 6 A, 115 V
Induction, continuous duty
10 A recommended
Laguna REVO 12|16
1 HP
Permanent-magnet DC with PWM control
15 A breaker
WEN 34035
6 A, 120 V; no HP stated
Not stated
Not stated
Rockler VS 12-24
1.2 HP, 120 V
Not stated
Not stated
NOVA Comet II DR
3/4 HP (550 W)
Permanent-magnet DC
Not stated
Horsepower is the maker’s rating, and makers don’t rate the same way. So we score bands, not exact figures: 1 HP or more scores 10, 3/4 HP scores 8, and a motor given only in amps scores 6. WEN lists 6 A, the same draw JET lists beside its 1 HP, but WEN doesn’t state horsepower, so we don’t guess one.
Laguna and NOVA use DC motors. Laguna says its PWM control keeps full torque at low speed, where simpler controllers lose it. NOVA says its 3/4 HP motor can produce more than its rating. Neither claim changes our score; the rating does.
Reverse and indexing: what each lathe has
Reverse helps when you sand. Indexing locks the spindle at even steps so you can mark flutes, beads or holes.
Lathe
Reverse
Index positions
Spacing
Where it’s stated
JET JWL-1221VS
Yes
24
15°
JET spec table; reverse in the listing
Laguna REVO 12|16
Yes, standard
24, with lock
15°
Laguna page and manual
WEN 34035
Yes, direction switch
24
15°
WEN manual
Rockler VS 12-24
Yes, sanding only
Not stated
None
Rockler page and manual
NOVA Comet II DR
Yes
12
30°
NOVA manual
Rockler’s manual says to use reverse only for sanding and never to cut with gouges or chisels while the work spins backward. WEN and Rockler both say to change direction only with the lathe off. If your chuck screws onto the spindle, reverse can loosen it, so stop and check it often.
WEN’s manual describes indexing as a way to create evenly spaced features around the work while the spindle is locked. With 24 positions you can divide work into 2, 3, 4, 6, 8, 12 or 24 equal parts. With 12 you lose 8 and 24.
Bed extensions and stands
Every maker here sells a bed extension. They differ in how much length each one states, and in the stand you’ll need.
Lathe
Bed extension
Stated result
Stand from the maker
JET JWL-1221VS
22-inch lathe bed extension
Not stated
Not on the pages read
Laguna REVO 12|16
10 in. expansion set; 20 in. bed extension
25-1/2 in. between centers, or 16 in. outboard (expansion set)
REVO 12|16 adjustable stand; wheel system
WEN 34035
Extension bed 34035EX
Not stated
Lathe stand LA8800
Rockler VS 12-24
Bed extension 71801
Spindles to 54 in.
Stand 72011; stand extension 73441
NOVA Comet II DR
Bed extension 47015
Bed extendable to 42 in.
Comet stand 47050; stand extension 47051
A benchtop lathe needs a heavy, stiff bench at the right height. NOVA’s manual says the stand should have enough weight and mass that it doesn’t move. A long extension also needs support under its far end, which is why NOVA and Rockler sell stand extensions to go with theirs.
Plan for dust as well. Turning throws shavings and fine sanding dust; our dust extractor guide covers machines that pull sanding dust from the work.
Warranty and weight
We show these but don’t score them: two makers state no warranty length on the pages we read, and weights are given on different bases.
Lathe
Warranty
Weight as stated
Basis
JET JWL-1221VS
Five years
121.25 net; 136.69 gross
JET spec table, no unit shown
Laguna REVO 12|16
Length not stated
118 lb; 125 lb shipping
Net and shipping
WEN 34035
Two years
125.7 lb
Manual spec table
Rockler VS 12-24
Length not stated
93 lb
With packaging
NOVA Comet II DR
1 year motor and controller; 2 years mechanical
84 lb (page); 77.2 lb packaged (manual)
Two NOVA figures
Weight helps a lathe sit still when a blank is off balance, which is why WEN’s listing makes a point of its 120-plus pounds. It also decides whether one person can lift the lathe onto a bench. Rockler’s manual tells you to get help if the lathe feels too heavy to lift alone.
Mini, midi or full-size lathe?
This page scores midi lathes only. Minis and full-size floor lathes are other kinds, with their own trade-offs.
Kind
Typical swing
Where it sits
Good for
Mini lathe
Under 12 in. (WEN LA3421: 8 in.)
Bench
Pens, ornaments, small spindles
Midi lathe (this page)
12 to 14 in.
Bench or its own stand
Bowls, legs, boxes, pens
Full-size lathe
Over 14 in.
Floor, on its own legs
Large bowls, platters, long work
A mini such as WEN’s LA3421, 8 by 13 in. per its listing, fits a small bench, but it can’t take a bowl wider than 8 in. A full-size lathe needs its own floor spot; the recalled Grizzly floor lathes below measure 62 to 72-1/2 in. wide. A midi sits between them and still lifts onto a bench.
Checked and left out
We checked this midi lathe but couldn’t tie its Amazon listing to one set of maker specs.
Lathe
Why it’s left out
What it does well
PSI Turncrafter Commander KWL-1218VS
The listing says 1 HP; Penn State Industries’ own page for the same item number lists 1.5 HP and 106 lb. We can’t tell which motor you’d get. Its lowest speed, 500 RPM, is also the highest floor we checked.
12 in. swing, 18 in. between centers, 24 indexing positions with a spindle lock, per the listing
When a listing and its maker disagree on the motor, we leave the lathe out rather than score a spec we can’t pin down. If Penn State Industries clears it up, we’ll check it again at the next update.
Recalls and lathe safety
We search the CPSC recall list for every brand on the page and for wood lathes in general.
Search on Oct 22, 2026
Recalls found
JET
None
Laguna
None
WEN
1, not a lathe (doorglass inserts by ODL, 2023)
Rockler
1, not a lathe (Murphy bed kits, 2018)
NOVA
6 for other products named Nova, none a lathe
Teknatool
None
Lathe
Grizzly G0584 and G0462, Shop Fox W1758 wood lathes, Nov 2, 2023
The 2023 recall covers Grizzly and Shop Fox floor lathes on cast-iron legs, none of them on this page. The CPSC says the cutting tool can break and strike the user or bystanders. About 21,300 were sold, plus about 60 in Canada, and Grizzly offers a free repair kit with an upgraded faceplate, tool rest and tool rest base.
WEN’s manual says to turn each new blank by hand before you switch on, to check it’s seated and clears the tool rest. Rockler’s says the bench must be strong enough to hold the lathe.
Where the sources disagree
Where two official sources give different figures, we show both and score the safer one.
Topic
One source says
Another says
Go by
NOVA bed extension
Amazon listing: adds 25.6 in.
NOVA manual: each extension adds 24.6 in.
Either way, a bed extension; scored the same
NOVA weight
NOVA page: 84 lb
NOVA manual: 77.2 lb packaged
Weight isn’t scored
NOVA quill travel
NOVA page: 1.6 in.
NOVA manual: 2 in.
Quill travel isn’t one of our checks
NOVA warranty
Page: 1 year motor and controller, 2 years mechanical
Manual: Teknatool two-year limited warranty
Ask NOVA about the motor
Rockler low speed range
Product page and listing: 300 to 1,100 RPM
Manual: 300 to 1,400 RPM
300 RPM floor either way
Rockler weight
Spec table: 93 lb with packaging
Same page: weight 94.00
Weight isn’t scored
JET length
Listing title: 12 x 21 in.
JET spec table: 20-1/4 in. between centers
20-1/4 in.
None of these changes a score. The biggest one for buyers is NOVA’s warranty: its page splits motor and mechanical coverage, while its manual names a two-year limited warranty. Register the lathe with NOVA and keep the receipt.
How to choose a wood lathe
Answer these in order. Each answer narrows the five picks.
Question
If yes
If no
Will you mostly turn bowls?
WEN (14 in. swing), or the Laguna for 16 in. outboard later
Any pick
Will you rough out wet or lopsided blanks?
JET (60 RPM) or Laguna (50 RPM)
Any pick
Will you turn spindles over 20 in.?
Rockler (24 in., 54 in. extended)
Any pick
Do you want to lay out flutes or spaced holes?
JET, Laguna or WEN (24 stops)
Any pick
Will it move off the bench often?
NOVA, the lightest boxed weight here
Any pick
Do you want the longest stated warranty?
JET (five years)
Any pick
Start with what you’ll turn most. Bowls want swing and a slow start; spindles want length. Then check your bench: stated weights run from 77.2 lb packaged for the NOVA to 125.7 lb for the WEN, so the bench has to carry that and stay put.
Plan for tools too. A lathe comes with centers and a faceplate, not gouges. WEN’s manual walks through a roughing gouge, spindle gouge, bowl gouge, skew chisel and parting tool. A chuck threaded 1 in. by 8 TPI fits all five picks.
Preparing blanks takes other machines. Our benchtop drill press guide covers drilling pen blanks and centers, and our drum sander guide covers flattening glued-up stock before it goes on the lathe.
Questions people ask
What is the best wood lathe?
Our top pick is the JET JWL-1221VS, which scores 9.7. It has a 1 HP motor, speeds from 60 to 3,600 RPM over three belt ranges, 24 indexing positions, a 12-1/2 in. swing, 20-1/4 in. between centers and a five-year warranty.
What is a wood lathe?
A machine that spins a piece of wood so you can shape it with handheld cutting tools. Spindle work, such as legs and pens, is held between two centers. Bowls are held on a faceplate or chuck on the headstock spindle.
What is a midi lathe?
A benchtop lathe between a mini and a full-size floor lathe, usually with a 12 to 14 in. swing. All five picks here are midi lathes, from the NOVA’s 12 in. to the WEN’s 14 in.
What size wood lathe should a beginner buy?
A midi lathe suits most beginners, because it turns pens and spindles and still takes a bowl. Pick by the work you’ll do most: the WEN 34035 for bowls, the Rockler VS 12-24 for spindles, or the JET JWL-1221VS for both.
What does swing mean on a lathe?
Swing over the bed is the largest diameter that clears the bed, twice the height from the bed to the spindle center. WEN gives its 34035 a 7 in. center height, which is its 14 in. swing.
What speed should I turn a bowl at?
Start slowly, as the Laguna, NOVA, Rockler and WEN manuals say, and speed up once the blank runs true. Rockler’s manual adds that bowl speeds are lower than spindle speeds, and the larger the diameter, the slower the speed.
Do I need reverse on a wood lathe?
It helps when sanding, because sanding both ways leaves fewer marks. All five picks reverse. Rockler’s manual says to use reverse only for sanding, never for cutting.
What chuck fits these lathes?
All five spindles are 1 in. by 8 TPI with an MT2 taper, so a chuck threaded 1 in. by 8 TPI fits each one. Laguna’s manual says outboard turning on the REVO needs a reversible chuck with set screws.
Can I make a wood lathe longer?
Yes. Each maker here sells a bed extension. Rockler says its 71801 takes the VS 12-24 to 54 in., NOVA says its bed is extendable to 42 in., and Laguna’s 10 in. expansion set takes the REVO to 25-1/2 in. between centers.
Is the JET JWL-1221VS reversible?
The Amazon listing says forward to reverse is a smooth transition. JET’s own spec table doesn’t list reverse, so we cite the listing.
How much does a wood lathe cost?
Prices move often, so each card shows today’s Amazon price with the time we read it. Three picks are sold by Amazon itself; the Rockler and NOVA are sold by their makers’ own Amazon stores.
How we pick wood lathes
How we pick
We looked at one kind of product: benchtop variable-speed midi wood lathes with a 12 to 14 in. swing on 120 V. Five lathes from five makers scored 7.0 or more and are picks. One more is shown as left out because its listing and maker disagree.
Every pick passed an offer read on Amazon at 7:45 AM on Oct 22, 2026: new, in stock and the buy-box winner. We matched each listing to the maker’s spec sheet or manual by model number.
Eight checks score 0 to 10 from published specs. Swing and motor count 2 each; between centers, lowest speed, reverse, indexing, speed readout and bed extension count 1 each. Warranty and weight aren’t scored.
Why trust us
Isaac Daniels, who owns Plain Buy Guides, edits this page. We read JET’s spec table, Laguna’s product page and manual, Rockler’s product page and manual, NOVA’s product page and manual and WEN’s product page and manual on Oct 22, 2026. Where two sources disagree, we show both. A CPSC search found no lathe recalls for any brand here.
Scoring: swing 10 at 14 in. or more, 9 at 12-1/2 in., 8 at 12 in. Between centers 10 at 24 in., 9 at 20 in., 8 at 16 in., 7 under 16 in. Motor 10 at 1 HP or more, 8 at 3/4 HP, 6 when no horsepower is stated.
Lowest speed 10 at 60 RPM or less, 8 at 250, 7 at 300. Reverse stated 10, not stated 4. Indexing 10 at 24 positions, 7 at 12, 4 not stated. A digital readout 10, none 4. A maker bed extension 10, none 4.
The spec score, check by check
Lathe
Swing
Centers
Motor
Low RPM
Reverse
Index
Readout
Extension
Score
JET JWL-1221VS
9
9
10
10
10
10
10
10
9.7
Laguna REVO 12|16
9
7
10
10
10
10
10
10
9.5
WEN 34035
10
9
6
8
10
10
10
10
8.9
Rockler VS 12-24
8
10
10
7
10
4
10
10
8.7
NOVA Comet II DR
8
8
8
8
10
7
10
10
8.5
Sources
JET Tools (jettools.com), JWL-1221VS 12 x 20 in. variable-speed wood lathe page and specifications
Laguna Tools (lagunatools.com), REVO 12|16 product page and owner’s manual
WEN Products (wenproducts.com), 34035 product page and operator’s manual
Rockler Woodworking and Hardware (rockler.com), VS 12-24 Variable Speed Midi Lathe page and instructions
NOVA Woodworking (teknatool.com), Comet II DR product page and owner’s manual
Penn State Industries (pennstateind.com), Turncrafter Commander KWL-1218VS page
U.S. Consumer Product Safety Commission recall list, searched by brand and for lathes on Oct 22, 2026
US keyword data for wood lathe searches, pulled Oct 22, 2026