Plain Buy Guides

As an Amazon Associate I earn from qualifying purchases. Links to Amazon on this page are affiliate links.

Watt Ready product guide

BLUETTI Elite 30 V2 Portable Power Station, 288Wh

Phones, laptops, routers and lights during short outages or trips

The Elite 30 V2 packs 288Wh of LFP storage and 600W of AC into a 9.5-pound case with 140W USB-C and a 10 ms UPS. Its 1,500W Power Lifting mode suits heating loads only, solar input is 200W, and ECO mode must be switched off for small always-on devices. It cannot take extra batteries.

Check this model on Amazon

Listing checked . Confirm the model, included parts and availability before ordering.

Published specifications

  • Manual: 288Wh LiFePO4; model Elite 30 V2
  • Manual: 600W AC total; Power Lifting to 1,500W resistive loads
  • Manual: AC input 380W; bypass 980W; UPS 10 ms or less
  • Manual: solar 12-28V, 10A, 200W max; car 12V or 24V
  • Manual: charge 32-104°F; discharge -4-104°F; IP20
  • Manual: 9.8 x 7 x 6.6 in, about 9.48 lb; page: 5-year warranty

Fit and limits

Strengths

  • 600W AC, 140W USB-C and a 10 ms UPS in a 9.5-pound unit
  • Detailed US manual with clear port, charging and storage limits
  • Pass-through charging up to 980W while plugged in

Caveats

  • ECO mode is on by default and can cut small or critical loads
  • No expansion; solar limited to 200W with the cable sold separately
  • 1,500W lifting runs heaters at reduced power, not full wattage

A 288Wh, 9.5-pound unit for small loads, not an expandable system

The Elite 30 V2 is BLUETTI's 288Wh lithium iron phosphate power station with a 600W inverter, weighing about 4.3 kg (9.48 lb) in the manual. The manual's specification page names the model Elite 30 V2. BLUETTI's FAQ says it does not support expansion batteries, though a separate BLUETTI B80 can charge it in power-bank mode.

In the box the manual lists the unit, a 1.8 m AC charging cable, a 0.72 m car charging cable, one M5 grounding screw and documentation. It states that the solar charging cable and the lead-acid battery charging cable are not included. The Amazon bullet lists the unit, AC cable, car cable and manual without the grounding screw.

600W continuous; the 1,500W figure is for heating loads only

The single AC outlet circuit is rated 600W in total at 120V and 5A. Power Lifting Mode, a maker feature that is off by default, lets the unit run pure resistive loads rated 600W to 1,500W. The manual stresses that actual output stays at 600W in this mode, so those appliances run at reduced power.

The manual's FAQ warns that devices with motors or compressors can start at two to four times their rated power and easily overload the unit, so keep total load under 600W. DC outputs are one 12V/10A car socket and two DC5521 ports at 12V/5A each, wired in parallel with a 10A combined limit. USB-C gives 100W and 140W; two USB-A ports give 15W each.

Charging: 380W from the wall, 200W from solar

AC input tops out at 380W. The manual lists Standard (default), Turbo and Silent charging modes, gives 80% in 45 minutes at 25°C for the fastest setting and estimates two to three hours for the slower ones. BLUETTI's page and the Amazon listing say 70 minutes to full at 380W. Generators must have pure sine wave output, and BLUETTI recommends its Grid Self-Adaption mode for them.

Solar input is 12 to 28V, 10A and 200W maximum, and the manual warns against panels with open-circuit voltage above 28V. Third-party panels with MC4 connectors are allowed, but not mixed panel types. The car input accepts 12V or 24V sockets, with the engine running. AC and solar together still cap at 380W.

UPS within 10 ms, but ECO mode can switch outputs off

Plugged into the wall, the unit passes grid power through to its outlets at up to 980W and switches to battery within 10 ms during an outage, according to the manual and BLUETTI's page. The manual adds that the UPS feature is not for data servers or workstations that need a high-performance UPS, and app modes include Standard, Time Control, PV Priority and Customized.

AC-ECO and DC-ECO modes are on by default and shut the outputs off after a period of low or no load. The manual says to disable ECO mode for small devices under 10W and for critical appliances such as lights. Anyone using this as a router or lamp backup should switch ECO off in settings or the app first.

Grounding, temperatures and storage routine

The manual says the unit must be grounded when charging from the grid and supplies an M5 grounding screw for that purpose. Charging is rated 32°F to 104°F, discharging -4°F to 104°F, and it carries an IP20 rating, so keep it dry.

For storage the manual asks for 40 to 60% charge, power off and cables disconnected, and a full cycle every three months; BLUETTI's page says to recharge to 40 to 60% every three to six months. If charge reaches zero, charge within 48 hours after holding the unit at 41°F to 95°F for six hours.

Efficiency claims, noise and warranty

BLUETTI's page and the listing quote 4.5W standby, while the manual's runtime formula uses self-consumption of about 9W, so use the higher figure for planning. The page lists 3,000-plus cycles to 80% of original capacity and a ten-year lifespan claim, and 30 dB noise under light loads without stating test distance.

BLUETTI's specification table lists a five-year warranty, and Amazon's warranty field says 60 months. Neither document read gives registration conditions or claim steps. Wi-Fi and Bluetooth are both listed for the BLUETTI app.

Check the current listing

Check this model on Amazon

Confirm the model, included parts and availability before ordering.

Primary sources

  1. BLUETTI Elite 30 V2 product page
  2. BLUETTI support page for the Elite 30 V2
  3. BLUETTI Elite 30 V2 user manual PDF (US English, V3.0)

Primary sources checked .

Compare with

Side-by-side pages, this model next to: OUPES Mega 1 Portable Power Station (S1), 1,024Wh, BLUETTI Apex 300 Portable Power Station, 2,764.8Wh.

Keep comparing

Use the Watt Ready product index to compare other models, or read the full buying guide for category-level advice.